|
1
|
VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED
• Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?
|
Yes
|
Go to the next step.
|
|
No
|
Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
|
|
2
|
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
• Verify related Service Information availability.
• Is any related Service Information available?
|
Yes
|
Perform repair or diagnosis according to the available Service Information.
• If the vehicle is not repaired, go to the next step.
|
|
No
|
Go to the next step.
|
|
3
|
INSPECT FUEL GAUGE SENDER UNIT CONNECTOR CONDITION
• Switch the ignition off.
• Disconnect the fuel gauge sender unit connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the connector and/or terminals, then go to Step 11.
|
|
No
|
Go to the next step.
|
|
4
|
INSPECT REAR BODY CONTROL MODULE (RBCM) CONNECTOR CONDITION
• Disconnect the rear body control module (RBCM) connector.
• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
• Is there any malfunction?
|
Yes
|
Repair or replace the connector and/or terminals, then go to Step 11.
|
|
No
|
Go to the next step.
|
|
5
|
INSPECT FUEL GAUGE SENDER UNIT CIRCUIT FOR SHORT TO GROUND
• Verify that the fuel gauge sender unit and rear body control module (RBCM) connectors are disconnected.
• Inspect for continuity between the following terminals (wiring harness-side) and body ground:
-
― Fuel gauge sender unit terminal A
― Fuel gauge sender unit terminal E
• Is there continuity?
|
Yes
|
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
• Fuel gauge sender unit terminal A—Rear body control module (RBCM) terminal 3N
• Fuel gauge sender unit terminal E—Rear body control module (RBCM) terminal 3I
If there is a common connector:
• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
• Repair or replace the malfunctioning part.
If there is no common connector:
• Repair or replace the wiring harness which has a short to ground.
Go to Step 11.
|
|
No
|
Go to the next step.
|
|
6
|
INSPECT FUEL GAUGE SENDER UNIT SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER
• Verify that the fuel gauge sender unit and rear body control module (RBCM) connectors are disconnected.
• Inspect for continuity between fuel gauge sender unit terminals E and C (wiring harness-side).
• Is there continuity?
|
Yes
|
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
• Fuel gauge sender unit terminal E—Rear body control module (RBCM) terminal 3I
• Fuel gauge sender unit terminal C—Rear body control module (RBCM) terminal 3C
If there is a common connector:
• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other.
• Repair or replace the malfunctioning part.
If there is no common connector:
• Repair or replace the wiring harness which has a short to each other.
Go to Step 11.
|
|
No
|
Go to the next step.
|
|
7
|
INSPECT FUEL GAUGE SENDER UNIT CIRCUIT FOR OPEN CIRCUIT
• Verify that the fuel gauge sender unit and rear body control module (RBCM) connectors are disconnected.
• Inspect for continuity between the following terminals (wiring harness-side):
-
― Fuel gauge sender unit terminal A—Rear body control module (RBCM) terminal 3N
― Fuel gauge sender unit terminal E—Rear body control module (RBCM) terminal 3I
• Is there continuity?
|
Yes
|
Go to the next step.
|
|
No
|
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
• Fuel gauge sender unit terminal A—Rear body control module (RBCM) terminal 3N
• Fuel gauge sender unit terminal E—Rear body control module (RBCM) terminal 3I
If there is a common connector:
• Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
• Repair or replace the malfunctioning part.
If there is no common connector:
• Repair or replace the wiring harness which has an open circuit.
Go to Step 11.
|
|
8
|
INSPECT FUEL GAUGE SENDER UNIT
• Inspect the fuel gauge sender unit.
• Is there any malfunction?
|
Yes
|
Replace the fuel gauge sender unit, then go to Step 11.
|
|
No
|
Go to the next step.
|
|
9
|
INSPECT REAR BODY CONTROL MODULE (RBCM)
• Inspect the rear body control module (RBCM).
• Is there any malfunction?
|
Yes
|
Replace the rear body control module (RBCM), then go to Step 11.
|
|
No
|
Go to the next step.
|
|
10
|
INSPECT INSTRUMENT CLUSTER
• Inspect the instrument cluster.
• Is there any malfunction?
|
Yes
|
Replace the instrument cluster, then go to the next step.
|
|
No
|
Go to the next step.
|
|
11
|
VERIFY DTC TROUBLESHOOTING COMPLETED
• Always reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Perform the KOEO or KOER self test.
• Is the PENDING CODE for this DTC present?
|
Yes
|
Repeat the inspection from Step 1.
• If the malfunction recurs, replace the PCM.
Go to the next step.
|
|
No
|
Go to the next step.
|
|
12
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the “AFTER REPAIR PROCEDURE”.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
|
|
No
|
DTC troubleshooting completed.
|
