DTC P0117:00 [SKYACTIV-D 1.5]

id0102q2701600

DTC P0117:00

ECT sensor circuit low input
DETECTION CONDITION
•  The PCM monitors the ECT sensor signal. If the PCM detects that the ECT sensor voltage at the PCM terminal 1CY is below 0.05 V for 5 s, the PCM determines that the ECT sensor circuit has a malfunction.
MONITORING CONDITIONS
―  Battery voltage: 8 V or more
―  0.5 s have elapsed after the ignition was switched ON (engine off or on)
Diagnostic support note
•  This is a continuous monitor (CCM).
•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.
•  FREEZE FRAME DATA/Snapshot data is available.
•  DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION
•  PCM restricts engine torque.
•  Inhibits the auto DPF regeneration control.
•  Inhibits the compulsory DPF regeneration control.
•  Inhibits the EGR control.
•  PCM restricts engine-transaxle integration control. (ATX)
•  Increase the idle speed.
•  Inhibits the A/C control.
•  Inhibits engine-stop by operating the i-stop function.
POSSIBLE CAUSE
•  Engine overheating (cooling system malfunction)
•  ECT sensor connector or terminals malfunction
•  ECT sensor malfunction
•  Short to ground in wiring harness between ECT sensor terminal A and PCM terminal 1CY
•  PCM connector or terminals malfunction
•  ECT sensor signal circuit and ground circuit are shorted to each other
•  PCM malfunction

Diagnostic Procedure

STEP

INSPECTION

ACTION
1
RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
Note
•  Recording can be facilitated using the screen capture function of the PC.
•  Record the FREEZE FRAME DATA/snapshot data on the repair order.
—
Go to the next step.
2
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY ENGINE CONDITION
•  Verify the engine condition.
•  Is the engine overheating?
Yes
Perform the symptom troubleshooting “NO.22 COOLING SYSTEM CONCERNS-OVERHEATING”.
(See NO.22 COOLING SYSTEM CONCERNS-OVERHEATING [SKYACTIV-D 1.5].)
No
Go to the next step.
4
INSPECT ECT SENSOR CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the ECT sensor connector.
•  Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
•  Is there any malfunction?
Yes
Repair or replace the connector and/or terminals, then go to Step 9.
No
Go to the next step.
5
DETERMINE IF ECT SENSOR OR WIRING HARNESS MALFUNCTION
•  Verify that the ECT sensor connector is disconnected.
•  Switch the ignition ON (engine off).
Note
•  Another DTC may be stored by the PCM detecting an open circuit.
•  Measure the voltage at the ECT sensor terminal A (wiring harness-side).
•  Is the voltage approx. 5 V?
Yes
Replace the ECT sensor, then go to Step 9.
(See ENGINE COOLANT TEMPERATURE (ECT) SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 1.5].)
No
Go to the next step.
6
INSPECT ECT SENSOR SIGNAL CIRCUIT FOR SHORT TO GROUND
•  Verify that the ECT sensor connector is disconnected.
•  Switch the ignition off.
•  Inspect for continuity between ECT sensor terminal A (wiring harness-side) and body ground.
•  Is there continuity?
Yes
Disconnect the PCM connector and inspect the wiring harness for short to ground.
•  If the short to ground circuit could be detected in the wiring harness:
―  Refer to the wiring diagram and verify whether or not there is a common connector between ECT sensor terminal A and PCM terminal 1CY.
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has a short to ground.
•  If the short to ground circuit could not be detected in the wiring harness:
―  Replace the PCM (short to ground in the PCM internal circuit).
Go to Step 9.
No
Go to the next step.
7
INSPECT PCM CONNECTOR CONDITION
•  Disconnect the PCM connector.
•  Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
•  Is there any malfunction?
Yes
Repair or replace the connector and/or terminals, then go to Step 9.
No
Go to the next step.
8
INSPECT ECT SENSOR SIGNAL CIRCUIT AND GROUND CIRCUIT FOR SHORT TO EACH OTHER
•  Verify that the ECT sensor and PCM connectors are disconnected.
•  Inspect for continuity between ECT sensor terminals A and B (wiring harness-side).
•  Is there continuity?
Yes
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
•  ECT sensor terminal A—PCM terminal 1CY
•  ECT sensor terminal B—PCM terminal 1CZ
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has a short to each other.
Go to the next step.
No
Go to the next step.
9
VERIFY DTC TROUBLESHOOTING COMPLETED
•  Always reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Perform the KOEO or KOER self test.
•  Is the same DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the PCM.
Go to the next step.
No
Go to the next step.
10
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [SKYACTIV-D 1.5].)
No
DTC troubleshooting completed.