DTC P1905:00 [SKYACTIV-D 1.5]

id0102q2968400

DTC P1905:00

Check connector circuit low input
DETECTION CONDITION
•  PCM detects that the check connector voltage is approx. 0 V for a continuous 0.016 s.
Diagnostic support note
•  This is an intermittent monitor (other).
•  The check engine light does not illuminate.
•  FREEZE FRAME DATA is not available.
•  Snapshot data is available.
•  DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION
Not applicable
POSSIBLE CAUSE
Note
•  If the fuel injection amount learning, compulsory DPF regeneration, timing chain learning, or engine oil data reset is performed without using the M-MDS, DTC P1905:00 may be detected by grounding the check connector (test terminal) to the body. In this case, DTC P1905:00 is automatically erased by disconnecting the check connector (test terminal) ground.
•  The purpose of DTC P1905:00 is to prevent forgetting to disconnect the check connector (test terminal) ground.
•  Short to ground in wiring harness between check connector terminal E and PCM terminal 2E
•  PCM connector or terminals malfunction
•  PCM malfunction

Diagnostic Procedure

STEP

INSPECTION

ACTION
1
RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
Note
•  Recording can be facilitated using the screen capture function of the PC.
•  Record the snapshot data on the repair order.
—
Go to the next step.
2
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
INSPECT CHECK CONNECTOR CIRCUIT FOR SHORT TO GROUND
•  Switch the ignition off.
•  Inspect for continuity between check connector terminal E (wiring harness-side) and body ground.
•  Is there continuity?
Yes
Disconnect the PCM connector and inspect the wiring harness for short to ground.
•  If the short to ground circuit could be detected in the wiring harness:
―  Refer to the wiring diagram and verify whether or not there is a common connector between check connector terminal E and PCM terminal 2E.
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has a short to ground.
•  If the short to ground circuit could not be detected in the wiring harness:
―  Replace the PCM (short to ground in the PCM internal circuit).
Go to Step 5.
No
Go to the next step.
4
INSPECT PCM CONNECTOR CONDITION
•  Disconnect the PCM connector.
•  Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
•  Is there any malfunction?
Yes
Repair or replace the connector and/or terminals, then go to the next step.
No
Go to the next step.
5
VERIFY DTC TROUBLESHOOTING COMPLETED
•  Always reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Perform the DTC Reading Procedure.
•  Is the same DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the PCM.
Go to the next step.
No
Go to the next step.
6
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [SKYACTIV-D 1.5].)
No
DTC troubleshooting completed.