DTC P0713:00 [FW6A-EL]

id050225817500

Applied VIN:

BM****** 1*****

DTC P0713:00

TFT sensor circuit high input

DETECTION CONDITION

•  Under the following conditions, the ATF temperature is −40 °C {−40 °F} or less for 5 s:

―  Battery voltage is 8 V or more.

―  IAT is −25 °C {−13 °F} or more.

―  IAT sensor related DTC is not recorded.

FAIL-SAFE FUNCTION

•  Inhibits learning control.

•  Inhibits neutral idle control.

•  Inhibits i-stop control.

POSSIBLE CAUSE

•  TFT sensor malfunction

•  Coupler component malfunction

•  TCM malfunction

SYSTEM WIRING DIAGRAM

Not applicable

DTC P0713:00	TFT sensor circuit high input
DETECTION CONDITION	• Under the following conditions, the ATF temperature is −40 °C {−40 °F} or less for 5 s: ― Battery voltage is 8 V or more. ― IAT is −25 °C {−13 °F} or more. ― IAT sensor related DTC is not recorded.
FAIL-SAFE FUNCTION	• Inhibits learning control. • Inhibits neutral idle control. • Inhibits i-stop control.
POSSIBLE CAUSE	• TFT sensor malfunction • Coupler component malfunction • TCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic procedure

STEP	INSPECTION		ACTION
1	CONFIRM IAT SENSOR PENDING CODE/DTC • Perform the PCM DTC inspection using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) • Are IAT sensor pending codes/DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
1		No	Go to the next step.
2	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture of the PC function. • Record the freeze frame data/snap shot data.	—	Go to the next step.
3	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, replace the control valve body. (See CONTROL VALVE BODY REMOVAL/INSTALLATION [FW6A-EL].) Go to the next step.
3		No	Replace the control valve body, then go to the next step. (See CONTROL VALVE BODY REMOVAL/INSTALLATION [FW6A-EL].)
4	VERIFY DTC TROUBLESHOOTING COMPLETED • Clear the DTC using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FW6A-EL].) • Perform the following procedure to ensure that the DTC has been resolved: 1. Switch the ignition to ON (engine off or on) and wait for 5 s or more. 2. Verify that the IAT is −25 °C {−13 °F} or more. • Perform the DTC inspection using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FW6A-EL].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [FW6A-EL].)
4		No	DTC troubleshooting completed.

Applied VIN:

BM****** 300001-

DTC P0713:00

TFT sensor circuit high input

DETECTION CONDITION

•  Under the following conditions, the ATF temperature is −40 °C {−40 °F} or less:

―  Battery voltage is 8 V or more.

―  The ECU internal temperature is the specified temperature or more.

―  ECU internal temperature sensor related DTC is not recorded.

FAIL-SAFE FUNCTION

•  Inhibits learning control.

•  Inhibits neutral idle control.

•  Inhibits i-stop control.

POSSIBLE CAUSE

•  TFT sensor malfunction

•  Coupler component malfunction

•  TCM malfunction

SYSTEM WIRING DIAGRAM

Not applicable

DTC P0713:00	TFT sensor circuit high input
DETECTION CONDITION	• Under the following conditions, the ATF temperature is −40 °C {−40 °F} or less: ― Battery voltage is 8 V or more. ― The ECU internal temperature is the specified temperature or more. ― ECU internal temperature sensor related DTC is not recorded.
FAIL-SAFE FUNCTION	• Inhibits learning control. • Inhibits neutral idle control. • Inhibits i-stop control.
POSSIBLE CAUSE	• TFT sensor malfunction • Coupler component malfunction • TCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic procedure

STEP	INSPECTION		ACTION
1	RECORD VEHICLE STATUS WHEN DTC WAS DETECTED TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture of the PC function. • Record the freeze frame data/snap shot data.	—	Go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, replace the control valve body. (See CONTROL VALVE BODY REMOVAL/INSTALLATION [FW6A-EL].) Go to the next step.
2		No	Replace the control valve body, then go to the next step. (See CONTROL VALVE BODY REMOVAL/INSTALLATION [FW6A-EL].)
3	VERIFY DTC TROUBLESHOOTING COMPLETED • Clear the DTC using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FW6A-EL].) • Perform the following procedure to ensure that the DTC has been resolved: 1. Switch the ignition ON (engine off or on) and wait for 5 s or more. 2. Inspect the value at the following TCM PIDs using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [FW6A-EL].) ― ECU_A ― ECU_B ― ECU_C 3. Verify that the average temperature of ECU_A, ECU_B, and ECU_C is 0 °C {32 °F} or more. • Perform the DTC inspection using the M-MDS. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FW6A-EL].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [FW6A-EL].)
3		No	DTC troubleshooting completed.