DTC P2135:00 [MZR 1.6]

DTC P2135:00	TP sensor No.1/No.2 voltage correlation problem
DETECTION CONDITION	• The PCM compares the input voltage from TP sensor No.1 with the input voltage from TP sensor No.2 when the engine is running. If the difference is more than the specification, the PCM determines that there is a TP sensor No.1/No.2 voltage correlation problem. Diagnostic support note • This is a continuous monitor (CCM). • The check engine light illuminates if the PCM detects the above malfunction condition in the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • DTC is stored in the PCM memory.
POSSIBLE CAUSE	• Throttle body connector or terminals malfunction • PCM connector or terminals malfunction • TP sensor No.1/No.2 malfunction • PCM malfunction

DTC P2135:00

TP sensor No.1/No.2 voltage correlation problem

DETECTION CONDITION

• The PCM compares the input voltage from TP sensor No.1 with the input voltage from TP sensor No.2 when the engine is running. If the difference is more than the specification, the PCM determines that there is a TP sensor No.1/No.2 voltage correlation problem.

Diagnostic support note

• This is a continuous monitor (CCM).

• The check engine light illuminates if the PCM detects the above malfunction condition in the first drive cycle.

• FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

• DTC is stored in the PCM memory.

POSSIBLE CAUSE

• Throttle body connector or terminals malfunction

• PCM connector or terminals malfunction

• TP sensor No.1/No.2 malfunction

• PCM malfunction

STEP	INSPECTION	ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
No	Go to the next step.
3	INSPECT THROTTLE BODY CONNECTOR CONDITION • Switch the ignition off. • Disconnect the throttle body connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector or terminals, then go to Step 6.
No	Go to the next step.
4	INSPECT PCM CONNECTOR CONDITION • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector or terminals, then go to Step 6.
No	Go to the next step.
5	INSPECT TP SENSOR NO.1/NO.2 • Reconnect all disconnected connectors. • Inspect the TP sensor No.1/No.2. (See THROTTLE POSITION (TP) SENSOR INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Replace the throttle body, then go to the next step. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZR 1.6].)
No	Go to the next step.
6	VERIFY DTC TROUBLESHOOTING COMPLETED • Always reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [MZR 1.6].) • Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST [MZR 1.6].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [MZR 1.6].) Go to the next step.
No	Go to the next step.
7	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [MZR 1.6].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [MZR 1.6].)
No	DTC troubleshooting completed.

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED

• Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?

Yes

Go to the next step.

Record the FREEZE FRAME DATA (Mode 2)/snapshot data on repair order, then go to the next step.

VERIFY RELATED SERVICE INFORMATION AVAILABILITY

• Verify related Service Information availability.

• Is any related Service Information available?

Yes

Perform repair or diagnosis according to the available Service Information.

• If the vehicle is not repaired, go to the next step.

Go to the next step.

INSPECT THROTTLE BODY CONNECTOR CONDITION

• Switch the ignition off.

• Disconnect the throttle body connector.

• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

• Is there any malfunction?

Yes

Repair or replace the connector or terminals, then go to Step 6.

Go to the next step.

INSPECT PCM CONNECTOR CONDITION

• Disconnect the PCM connector.

• Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

• Is there any malfunction?

Yes

Repair or replace the connector or terminals, then go to Step 6.

Go to the next step.

INSPECT TP SENSOR NO.1/NO.2

• Reconnect all disconnected connectors.

• Inspect the TP sensor No.1/No.2.

(See THROTTLE POSITION (TP) SENSOR INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Replace the throttle body, then go to the next step.

(See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

VERIFY DTC TROUBLESHOOTING COMPLETED

• Always reconnect all disconnected connectors.

• Clear the DTC from the PCM memory using the M-MDS.

(See AFTER REPAIR PROCEDURE [MZR 1.6].)

• Perform the KOEO or KOER self test.

(See KOEO/KOER SELF TEST [MZR 1.6].)

• Is the same DTC present?

Yes

Repeat the inspection from Step 1.

• If the malfunction recurs, replace the PCM.

(See PCM REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

• Perform the “AFTER REPAIR PROCEDURE”.

(See AFTER REPAIR PROCEDURE [MZR 1.6].)

• Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [MZR 1.6].)

DTC troubleshooting completed.