DTC U2300:00 [SKYACTIV-D 1.5]

id0102q2228300

DTC U2300:00

Global central configuration error
DETECTION CONDITION
•  With the battery voltage more than specified value, the following conditions is continuously met for 5 s.
―  No configuration of the instrument cluster.
―  The configuration signal with the estimated CAN ID is not sent from the instrument cluster.
―  The configuration signal value sent via CAN from the instrument cluster is unknown or invalid.
―  The configuration signal value sent via CAN from the instrument cluster is a value other than the estimated value.
―  The configuration signal value sent via CAN from the instrument cluster does not match the PCM value.
Diagnostic support note
•  This is an intermittent monitor (other).
•  The check engine light does not illuminate.
•  FREEZE FRAME DATA is not available.
•  Snapshot data is available.
•  DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION
Not applicable
POSSIBLE CAUSE
•  CAN drive error (instrument cluster or PCM)
•  Configuration data for the instrument cluster is incorrectly set
•  CAN communication line malfunction between instrument cluster and PCM
―  Instrument cluster terminal B—Front body control module (FBCM) terminal 2P
―  Instrument cluster terminal D—Front body control module (FBCM) terminal 2N
―  Front body control module (FBCM) terminal 2K—PCM terminal 2C
―  Front body control module (FBCM) terminal 2I—PCM terminal 2D
•  Front body control module (FBCM) malfunction
•  PCM connector or terminals malfunction
•  Instrument cluster connector or terminals malfunction
•  Instrument cluster loose
•  Instrument cluster malfunction
•  Error in non-volatile memory in PCM
•  PCM malfunction

Diagnostic Procedure

STEP

INSPECTION

ACTION
1
RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
Note
•  Recording can be facilitated using the screen capture function of the PC.
•  Record the snapshot data on the repair order.
—
Go to the next step.
2
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY DTC FOR MODULE COMMUNICATION
•  Switch the ignition off, then ON (engine off).
•  Perform the DTC Reading Procedure.
•  Is the DTC U0155:00 also present?
Yes
Go to the applicable DTC inspection.
(See DTC U0073:00, U0101:00, U0104:00, U0121:00, U0131:00, U0140:00, U0151:00, U0155:00, U0214:00, U0235:00 [SKYACTIV-D 1.5].)
No
Go to the next step.
4
CONFIRM FRONT BODY CONTROL MODULE (FBCM) DTC
•  Perform the front body control module (FBCM) DTC inspection using the M-MDS.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [FRONT BODY CONTROL MODULE (FBCM)].)
No
Go to the next step.
5
CONFIRM INSTRUMENT CLUSTER DTC
•  Perform the instrument cluster DTC inspection using the M-MDS.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [INSTRUMENT CLUSTER].)
No
Go to the next step.
6
INSPECT PCM CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the PCM connector.
•  Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
•  Is there any malfunction?
Yes
Repair or replace the connector and/or terminals, then go to Step 10.
No
Go to the next step.
7
INSPECT INSTRUMENT CLUSTER CONNECTOR CONDITION
•  Disconnect the instrument cluster connector.
•  Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
•  Is there any malfunction?
Yes
Repair or replace the connector and/or terminals, then go to Step 10.
No
Go to the next step.
8
INSPECT INSTALLATION OF INSTRUMENT CLUSTER
•  Inspect installation of instrument cluster.
•  Is the instrument cluster installed securely?
Yes
Go to the next step.
No
Retighten the instrument cluster, then go to Step 10.
(See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
9
INSPECT INSTRUMENT CLUSTER
•  Inspect the instrument cluster.
•  Is there any malfunction?
Yes
Replace the instrument cluster, then go to the next step.
(See INSTRUMENT CLUSTER REMOVAL/INSTALLATION.)
No
Go to the next step.
10
VERIFY DTC TROUBLESHOOTING COMPLETED
•  Always reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Switch the ignition ON (engine off) and wait for 15 s or more.
•  Switch the ignition off.
•  Wait until the main relay is off (approx. 1 min).
•  Perform the DTC Reading Procedure.
•  Is the same DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the PCM.
Go to the next step.
No
Go to the next step.
11
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [SKYACTIV-D 1.5].)
No
DTC troubleshooting completed.