DTC P05A0:00 [SKYACTIV-D 1.5]

id0102q2402200

DTC P05A0:00

Active air shutter: Opening angle abnormality (sticking)

DETECTION CONDITION

•  Active air shutter opening angle is certain value or less while intake air temperature is 5 °C {41 °F} or more.

Diagnostic support note

•  This is an intermittent monitor (other).

•  The check engine light does not illuminate.

•  FREEZE FRAME DATA is not available.

•  Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  Performs fully open/closed position learning function three times.

POSSIBLE CAUSE

•  Foreign matter caught in active air shutter

•  Active air shutter malfunction

•  PCM malfunction

SYSTEM WIRING DIAGRAM

Not applicable

DTC P05A0:00	Active air shutter: Opening angle abnormality (sticking)
DETECTION CONDITION	• Active air shutter opening angle is certain value or less while intake air temperature is 5 °C {41 °F} or more. Diagnostic support note • This is an intermittent monitor (other). • The check engine light does not illuminate. • FREEZE FRAME DATA is not available. • Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• Performs fully open/closed position learning function three times.
POSSIBLE CAUSE	• Foreign matter caught in active air shutter • Active air shutter malfunction • PCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture function of the PC. • Record the snapshot data on the repair order.	—	Go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY DTC RELATED TO ACTIVE AIR SHUTTER • Switch the ignition off, then ON (engine off). • Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 1.5].) • Is the PENDING CODE/DTC U0284:00 also present?	Yes	Go to the applicable PENDING CODE or DTC inspection. (See DTC U0284:00 [SKYACTIV-D 1.5].)
3		No	Go to the next step.
4	VERIFY IF FOREIGN MATTER IS LODGED • Verify if the active air shutter has lodged foreign matter. • Has the active air shutter lodged any foreign matter?	Yes	Remove the foreign matter, then go to Step 6.
4		No	Go to the next step.
5	INSPECT ACTIVE AIR SHUTTER • Inspect the active air shutter. (See ACTIVE AIR SHUTTER INSPECTION.) • Is there any malfunction?	Yes	Replace the active air shutter, then go to the next step. (See ACTIVE AIR SHUTTER REMOVAL/INSTALLATION.)
5		No	Go to the next step.
6	VERIFY DTC TROUBLESHOOTING COMPLETED • Always reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC [SKYACTIV-D 1.5].) • Start the engine. • Drive the vehicle at 10 km/h {6.2 mph} or more for approx. 1 min. • Perform the DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 1.5].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 1.5].) Go to the next step.
6		No	Go to the next step.
7	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [SKYACTIV-D 1.5].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-D 1.5].)
7		No	DTC troubleshooting completed.