DTC P0476:00 [SKYACTIV-D 1.5]

id0102q2856100

DTC P0476:00

Exhaust shutter valve control duty signal error

DETECTION CONDITION

•  When the following condition is met, the exhaust shutter valve control duty value is 90% or more for a continuos 2 s.

MONITORING CONDITIONS

―  During engine running

―  The following DTCs are not detected:

•  PCM internal CPU: P0606:00

•  Exhaust shutter valve DC motor control: P0475:00

•  Exhaust shutter valve position sensor: P048D:00, P048E:00

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA/Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  PCM restricts engine torque.

•  Inhibits the EGR control.

•  Inhibits the auto DPF regeneration control.

•  Inhibits the compulsory DPF regeneration control.

•  Inhibits engine-stop by operating the i-stop function.

POSSIBLE CAUSE

•  Exhaust shutter valve connector or terminals malfunction

•  PCM connector or terminals malfunction

•  Open circuit in wiring harness between the following terminals:

―  Exhaust shutter valve terminal E—PCM terminal 1AO

―  Exhaust shutter valve terminal F—PCM terminal 1AJ

•  Exhaust shutter valve position sensor malfunction

•  Exhaust shutter valve malfunction

•  PCM malfunction

DTC P0476:00	Exhaust shutter valve control duty signal error
DETECTION CONDITION	• When the following condition is met, the exhaust shutter valve control duty value is 90% or more for a continuos 2 s. MONITORING CONDITIONS ― During engine running ― The following DTCs are not detected: • PCM internal CPU: P0606:00 • Exhaust shutter valve DC motor control: P0475:00 • Exhaust shutter valve position sensor: P048D:00, P048E:00 Diagnostic support note • This is a continuous monitor (CCM). • The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA/Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• PCM restricts engine torque. • Inhibits the EGR control. • Inhibits the auto DPF regeneration control. • Inhibits the compulsory DPF regeneration control. • Inhibits engine-stop by operating the i-stop function.
POSSIBLE CAUSE	• Exhaust shutter valve connector or terminals malfunction • PCM connector or terminals malfunction • Open circuit in wiring harness between the following terminals: ― Exhaust shutter valve terminal E—PCM terminal 1AO ― Exhaust shutter valve terminal F—PCM terminal 1AJ • Exhaust shutter valve position sensor malfunction • Exhaust shutter valve malfunction • PCM malfunction

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION Note • Recording can be facilitated using the screen capture function of the PC. • Record the FREEZE FRAME DATA/snapshot data on the repair order.	—	Go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT EXHAUST SHUTTER VALVE CONNECTOR CONDITION • Switch the ignition off. • Disconnect the exhaust shutter valve connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 7.
3		No	Go to the next step.
4	INSPECT PCM CONNECTOR CONDITION • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 7.
4		No	Go to the next step.
5	INSPECT EXHAUST SHUTTER VALVE CIRCUIT FOR OPEN CIRCUIT • Verify that the exhaust shutter valve and PCM connectors are disconnected. • Inspect for continuity between the following terminals (wiring harness-side): ― Exhaust shutter valve terminal E—PCM terminal 1AO ― Exhaust shutter valve terminal F—PCM terminal 1AJ • Is there continuity?	Yes	Go to the next step.
5		No	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: • Exhaust shutter valve terminal E—PCM terminal 1AO • Exhaust shutter valve terminal F—PCM terminal 1AJ If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has an open circuit. Go to Step 7.
6	INSPECT EXHAUST SHUTTER VALVE POSITION SENSOR • Reconnect all disconnected connectors. • Inspect the exhaust shutter valve position sensor. (See EXHAUST SHUTTER VALVE POSITION SENSOR INSPECTION [SKYACTIV-D 1.5].) • Is there any malfunction?	Yes	Inspect the exhaust shutter valve, then go to the next step. (See EXHAUST SHUTTER VALVE INSPECTION [SKYACTIV-D 1.5].)
6		No	Go to the next step.
7	VERIFY DTC TROUBLESHOOTING COMPLETED • Always reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC [SKYACTIV-D 1.5].) • Start the engine and leave it idling for 1 min. • Perform the DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 1.5].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 1.5].) Go to the next step.
7		No	Go to the next step.
8	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [SKYACTIV-D 1.5].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-D 1.5].)
8		No	DTC troubleshooting completed.