DTC P0384:00 [SKYACTIV-D 2.2]

id0102s4038400

DTC P0384:00

Glow control module circuit high input

DETECTION CONDITION

•  The PCM monitors the input current from the glow control module. If the input current is above 5.9 A for 5 s, the PCM determines that the glow control module circuit has a malfunction.

MONITORING CONDITIONS

―  Battery voltage: 9—16 V

―  0.5 s have elapsed after the ignition was switched ON

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  Inhibits engine-stop by operating the i-stop function.

POSSIBLE CAUSE

•  Glow control module connector or terminals malfunction

•  Open circuit in wiring harness between glow control module terminal 2A and body ground

―  GLOW SIG 5 A fuse malfunction

•  PCM connector or terminals malfunction

•  Short to power supply in wiring harness between the following terminals:

―  Glow control module terminal 2B—PCM terminal 2I

―  Glow control module terminal 2E—PCM terminal 2BA

•  Open circuit in wiring harness between the following terminals:

―  Glow control module terminal 2B—PCM terminal 2I

―  Glow control module terminal 2E—PCM terminal 2BA

•  Glow control module malfunction

•  PCM malfunction

DTC P0384:00	Glow control module circuit high input
DETECTION CONDITION	• The PCM monitors the input current from the glow control module. If the input current is above 5.9 A for 5 s, the PCM determines that the glow control module circuit has a malfunction. MONITORING CONDITIONS ― Battery voltage: 9—16 V ― 0.5 s have elapsed after the ignition was switched ON Diagnostic support note • This is a continuous monitor (CCM). • The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• Inhibits engine-stop by operating the i-stop function.
POSSIBLE CAUSE	• Glow control module connector or terminals malfunction • Open circuit in wiring harness between glow control module terminal 2A and body ground ― GLOW SIG 5 A fuse malfunction • PCM connector or terminals malfunction • Short to power supply in wiring harness between the following terminals: ― Glow control module terminal 2B—PCM terminal 2I ― Glow control module terminal 2E—PCM terminal 2BA • Open circuit in wiring harness between the following terminals: ― Glow control module terminal 2B—PCM terminal 2I ― Glow control module terminal 2E—PCM terminal 2BA • Glow control module malfunction • PCM malfunction

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	INSPECT GLOW CONTROL MODULE CONNECTOR CONDITION • Switch the ignition off. • Disconnect the glow control module connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
3		No	Go to the next step.
4	INSPECT GLOW CONTROL MODULE GROUND CIRCUIT FOR OPEN CIRCUIT • Verify that the glow control module connector is disconnected. • Inspect for continuity between glow control module terminal 2A (wiring harness-side) and body ground. • Is there continuity?	Yes	Go to the next step.
4		No	Inspect the GLOW SIG 5 A fuse. • If the fuse is blown or deteriorated: ― Replace the fuse. • If the fuse is normal: ― Refer to the wiring diagram and verify whether or not there is a common connector between glow control module terminal 2A and body ground. If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has an open circuit. Go to Step 9.
5	INSPECT PCM CONNECTOR CONDITION • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 9.
5		No	Go to the next step.
6	INSPECT GLOW CONTROL MODULE CIRCUIT FOR SHORT TO POWER SUPPLY • Verify that the glow control module and PCM connectors are disconnected. • Switch the ignition ON (engine off). • Measure the voltage at the following terminals (wiring harness-side): ― Glow control module terminal 2B ― Glow control module terminal 2E • Is the voltage 0 V?	Yes	Go to the next step.
6		No	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: • Glow control module terminal 2B—PCM terminal 2I • Glow control module terminal 2E—PCM terminal 2BA If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has a short to power supply. Go to Step 9.
7	INSPECT GLOW CONTROL MODULE CIRCUIT FOR OPEN CIRCUIT • Verify that the glow control module and PCM connectors are disconnected. • Switch the ignition off. • Inspect for continuity between the following terminals (wiring harness-side): ― Glow control module terminal 2B—PCM terminal 2I ― Glow control module terminal 2E—PCM terminal 2BA • Is there continuity?	Yes	Go to the next step.
7		No	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: • Glow control module terminal 2B—PCM terminal 2I • Glow control module terminal 2E—PCM terminal 2BA If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has an open circuit. Go to Step 9.
8	INSPECT GLOW CONTROL MODULE • Inspect the glow control module. (See GLOW PLUG CONTROL MODULE INSPECTION [SKYACTIV-D 2.2].) • Is there any malfunction?	Yes	Replace the glow control module, then go to the next step. (See GLOW PLUG CONTROL MODULE REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
8		No	Go to the next step.
9	VERIFY DTC TROUBLESHOOTING COMPLETED • Always reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [SKYACTIV-D 2.2].) • Perform the DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 2.2].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].) Go to the next step.
9		No	Go to the next step.
10	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [SKYACTIV-D 2.2].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-D 2.2].)
10		No	DTC troubleshooting completed.