DTC P1676:00 [SKYACTIV-D 2.2]

id0102s4149900

DTC P1676:00

Fuel injector code mistakenly programmed

DETECTION CONDITION

•  The fuel injector identification number is mistakenly programmed into the PCM for a continuous 1 s when the following condition is met.

MONITORING CONDITIONS

―  Ignition switched ON (engine off or on)

Diagnostic support note

•  This is an intermittent monitor (fuel system).

•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  PCM restricts engine torque.

•  Inhibits the EGR control.

•  Inhibits the diesel particulate filter regeneration control.

•  Inhibits engine-stop by operating the i-stop function.

•  PCM restricts engine-transaxle integration control.

POSSIBLE CAUSE

•  Fuel injector code program is not performed correctly.

•  PCM malfunction

SYSTEM WIRING DIAGRAM

Not applicable

DTC P1676:00	Fuel injector code mistakenly programmed
DETECTION CONDITION	• The fuel injector identification number is mistakenly programmed into the PCM for a continuous 1 s when the following condition is met. MONITORING CONDITIONS ― Ignition switched ON (engine off or on) Diagnostic support note • This is an intermittent monitor (fuel system). • The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• PCM restricts engine torque. • Inhibits the EGR control. • Inhibits the diesel particulate filter regeneration control. • Inhibits engine-stop by operating the i-stop function. • PCM restricts engine-transaxle integration control.
POSSIBLE CAUSE	• Fuel injector code program is not performed correctly. • PCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED • Have the FREEZE FRAME DATA (Mode 2)/snapshot data and DIAGNOSTIC MONITORING TEST RESULTS (fuel system related) been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data and DIAGNOSTIC MONITORING TEST RESULTS on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	PERFORM FUEL INJECTOR CODE PROGRAM • Perform the “FUEL INJECTOR CODE PROGRAM”. (See FUEL INJECTOR CODE PROGRAM [SKYACTIV-D 2.2].) • Is the fuel injector code programmed correctly?	Yes	Go to the next step.
3		No	Perform the “FUEL INJECTOR DATA RESET”. (See FUEL INJECTOR DATA RESET [SKYACTIV-D 2.2].) Perform the “FUEL INJECTOR CODE PROGRAM” again. (See FUEL INJECTOR CODE PROGRAM [SKYACTIV-D 2.2].) Go to the next step.
4	VERIFY DTC TROUBLESHOOTING COMPLETED • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [SKYACTIV-D 2.2].) • Perform the DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 2.2].) • Is the same DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
4		No	Go to the next step.
5	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [SKYACTIV-D 2.2].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-D 2.2].)
5		No	DTC troubleshooting completed.