DTC P0108:00 [SKYACTIV-D 2.2]

id0102s4701200

DTC P0108:00

MAP sensor No.2 circuit high input
DETECTION CONDITION
•  The PCM monitors the input voltage from the MAP sensor No.2. If the input voltage at the PCM terminal 1CQ is above 4.91 V for 4 s, the PCM determines that the MAP sensor No.2 circuit has a malfunction.
MONITORING CONDITIONS
―  Battery voltage: 8—20 V
―  0.5 s have elapsed after the ignition was switched ON (engine off or on)
Diagnostic support note
•  This is a continuous monitor (CCM).
•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.
•  FREEZE FRAME DATA (Mode 2)/Snapshot data is available.
•  DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION
•  PCM restricts engine torque.
•  Inhibits the EGR control.
•  Inhibits the diesel particulate filter regeneration control.
•  Inhibits engine-stop by operating the i-stop function.
•  PCM restricts engine-transaxle integration control.
POSSIBLE CAUSE
•  Turbocharger malfunction
•  MAP sensor No.2 connector or terminals malfunction
•  PCM connector or terminals malfunction
•  Short to power supply in wiring harness between MAP sensor No.2 terminal D and PCM terminal 1CQ
•  MAP sensor No.2 power supply circuit and signal circuit are shorted to each other
•  Open circuit in wiring harness between the following terminals:
―  MAP sensor No.2 terminal D—PCM terminal 1CQ
―  MAP sensor No.2 terminal A—PCM terminal 1CR
•  MAP sensor No.2 malfunction
•  PCM malfunction

Diagnostic Procedure

STEP

INSPECTION

ACTION
1
VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED
•  Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
2
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY RELATED PENDING CODE AND/OR DTC
•  Switch the ignition off, then ON (engine off).
•  Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
•  Are any other PENDING CODEs and/or DTCs present?
Yes
Go to the applicable PENDING CODE or DTC inspection.
(See DTC TABLE [SKYACTIV-D 2.2].)
No
Go to the next step.
4
INSPECT MAP SENSOR NO.2 CONNECTOR CONDITION
•  Switch the ignition off.
•  Disconnect the MAP sensor No.2 connector.
•  Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
•  Is there any malfunction?
Yes
Repair or replace the connector and/or terminals, then go to Step 10.
No
Go to the next step.
5
INSPECT PCM CONNECTOR CONDITION
•  Disconnect the PCM connector.
•  Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
•  Is there any malfunction?
Yes
Repair or replace the connector and/or terminals, then go to Step 10.
No
Go to the next step.
6
INSPECT MAP SENSOR NO.2 SIGNAL CIRCUIT FOR SHORT TO POWER SUPPLY
•  Verify that the MAP sensor No.2 and PCM connectors are disconnected.
•  Switch the ignition ON (engine off).
•  Measure the voltage at the MAP sensor No.2 terminal D (wiring harness-side).
•  Is the voltage 0 V?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify whether or not there is a common connector between MAP sensor No.2 terminal D and PCM terminal 1CQ.
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to power supply.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has a short to power supply.
Go to Step 10.
7
INSPECT MAP SENSOR NO.2 POWER SUPPLY CIRCUIT AND SIGNAL CIRCUIT FOR SHORT TO EACH OTHER
•  Verify that the MAP sensor No.2 and PCM connectors are disconnected.
•  Switch the ignition off.
•  Inspect for continuity between MAP sensor No.2 terminals C and D (wiring harness-side).
•  Is there continuity?
Yes
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
•  MAP sensor No.2 terminal C—PCM terminal 1CN
•  MAP sensor No.2 terminal D—PCM terminal 1CQ
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to each other.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has a short to each other.
Go to Step 10.
No
Go to the next step.
8
INSPECT MAP SENSOR NO.2 CIRCUIT FOR OPEN CIRCUIT
•  Verify that the MAP sensor No.2 and PCM connectors are disconnected.
•  Inspect for continuity between the following terminals (wiring harness-side):
―  MAP sensor No.2 terminal D—PCM terminal 1CQ
―  MAP sensor No.2 terminal A—PCM terminal 1CR
•  Is there continuity?
Yes
Go to the next step.
No
Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:
•  MAP sensor No.2 terminal D—PCM terminal 1CQ
•  MAP sensor No.2 terminal A—PCM terminal 1CR
If there is a common connector:
•  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for an open circuit.
•  Repair or replace the malfunctioning part.
If there is no common connector:
•  Repair or replace the wiring harness which has an open circuit.
Go to Step 10.
9
INSPECT MAP SENSOR NO.2
•  Reconnect all disconnected connectors.
•  Inspect the MAP sensor No.2.
•  Is there any malfunction?
Yes
Replace the MAP sensor No.2, then go to the next step.
(See MANIFOLD ABSOLUTE PRESSURE (MAP) SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
No
Go to the next step.
10
VERIFY DTC TROUBLESHOOTING COMPLETED
•  Always reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Perform the KOEO or KOER self test.
•  Is the same DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the PCM.
Go to the next step.
No
Go to the next step.
11
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [SKYACTIV-D 2.2].)
No
DTC troubleshooting completed.