DTC P0500:00 [SKYACTIV-D 2.2]

id0102s4704800

DTC P0500:00

VSS circuit problem

DETECTION CONDITION

•  With the following conditions met, a condition has continued for 5 s in which an error signal from the DSC HU/CM is received or no signal can be received from the DSC HU/CM.

MONITORING CONDITIONS

―  Battery voltage: above 10 V

―  1.5 s have elapsed since engine was started 1.5 s after ignition is switched ON (engine off)

Diagnostic support note

•  This is a continuous monitor (CCM).

•  The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle.

•  FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  PCM restricts engine torque.

•  Inhibits the EGR control.

•  Inhibits the diesel particulate filter regeneration control.

•  Inhibits the A/C control.

•  Inhibits engine-stop by operating the i-stop function.

POSSIBLE CAUSE

•  DSC HU/CM DTC is stored.

―  CAN communication line malfunction between PCM and DSC HU/CM

―  DSC HU/CM connector or terminals malfunction

―  Front ABS wheel-speed sensor malfunction

―  DSC HU/CM malfunction

•  PCM malfunction

SYSTEM WIRING DIAGRAM

Not applicable

DTC P0500:00	VSS circuit problem
DETECTION CONDITION	• With the following conditions met, a condition has continued for 5 s in which an error signal from the DSC HU/CM is received or no signal can be received from the DSC HU/CM. MONITORING CONDITIONS ― Battery voltage: above 10 V ― 1.5 s have elapsed since engine was started 1.5 s after ignition is switched ON (engine off) Diagnostic support note • This is a continuous monitor (CCM). • The check engine light illuminates if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• PCM restricts engine torque. • Inhibits the EGR control. • Inhibits the diesel particulate filter regeneration control. • Inhibits the A/C control. • Inhibits engine-stop by operating the i-stop function.
POSSIBLE CAUSE	• DSC HU/CM DTC is stored. ― CAN communication line malfunction between PCM and DSC HU/CM ― DSC HU/CM connector or terminals malfunction ― Front ABS wheel-speed sensor malfunction ― DSC HU/CM malfunction • PCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY STORED DTC IN DSC HU/CM • Retrieve the DSC HU/CM DTC using the M-MDS. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)
3		No	Go to the next step.
4	VERIFY DTC TROUBLESHOOTING COMPLETED • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [SKYACTIV-D 2.2].) • Drive the vehicle. • Perform the KOEO or KOER self test. (See KOEO/KOER SELF TEST [SKYACTIV-D 2.2].) • Is the PENDING CODE for this DTC present?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
4		No	Go to the next step.
5	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [SKYACTIV-D 2.2].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-D 2.2].)
5		No	DTC troubleshooting completed.