ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [GW6A-EL]

id050228290100


Reading DTCs Procedure

1.  Connect the M-MDS to the DLC-2.

2.  After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

(1)  Select “Self Test”.
(2)  Select “Modules”.
(3)  Select “TCM”.

Note
•  Freeze frame data/snapshot data appears at the top of the help screen when the displayed DTC is selected.
Freeze frame data
•  The freeze frame data consists of data for vehicle and transaxle control system operation conditions when malfunctions in the transaxle control system are detected and stored in the TCM.
•  Freeze frame data is stored at the instant the malfunction indicator lamp illuminates, and only a part of the DTC data is stored.
Snapshot data
•  The data for all DTCs currently detected is stored.
Recorded DTC timing
―  For DTCs with one drive cycle, data is recorded during the malfunction determination period.
―  For DTCs with two drive cycles, data is recorded during non-determination (1st diagnosis) periods.

3.  Then, select the “Retrieve CMDTCs” and perform procedures according to the directions on the M-MDS screen.

4.  Verify the DTC according to the directions on the screen.

•  If any DTCs are displayed, perform troubleshooting according to the corresponding DTC inspection.

5.  After completion of repairs, clear all DTCs stored in the TCM. (See Freeze frame data item table.)


Freeze frame data item table

Note
•  Refer to PID/DATA monitor table for confirm the transaxle control system operation status while the TCM does not store the DTC. (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [GW6A-EL].)
•  Freeze frame data items are not displayed, according to detected DTC.

—: Not applicable

Freeze frame data item

Unit

Description

Corresponding PID/DATA monitor item
LOAD
%
Calculated engine load
—
ECT
°C {°F}
Engine coolant temperature
ECT
RPM
RPM
Engine speed
RPM
VS
KPH {MPH}
Vehicle speed
VSS
IAT
°C {°F}
Intake air temperature
—
TP
%
Throttle valve position No.1
—
RUNTM
hh:mm:ss
Time from engine start
—
VPWR
V
Module supply voltage
VPWR
APP_D
%
Accelerator pedal position No.1
APP1


Snapshot data item table

Note
•  Refer to PID/DATA monitor table for confirm the transaxle control system operation status while the TCM does not store the DTC. (See ON-BOARD DIAGNOSTIC SYSTEM PID/DATA MONITOR INSPECTION [GW6A-EL].)
•  Snapshot data items are not displayed, according to detected DTC.

—: Not applicable

Snapshot data item

Unit

Description

Corresponding PID/DATA monitor item
LOAD
%
Calculated engine load
—
ECT
°C {°F}
Engine coolant temperature
ECT
RPM
RPM
Engine speed
RPM
VSS
KPH {MPH}
Vehicle speed
VSS
IAT
°C {°F}
Intake air temperature
—
EG_RUN_TIME
—
Time from engine start
—
VPWR
V
Module supply voltage
VPWR
APP1
%
Accelerator pedal position No.1
APP1
GEAR_SEL
1/2/3/4/5/6
Gear shift position
GEAR_SEL
TSS
RPM
Turbine/input shaft speed
TSS
TFT
°C {°F}
ATF temperature
TFT
OSS
RPM
Output shaft speed
OSS
LOCK_UP
Off/SLIP/On
Torque converter (TCC condition)
LOCK_UP
OIL_PRES_SW2
Off/On
Oil pressure switch No.2 condition
OP_SW2
OIL_PRES_SW1
Off/On
Oil pressure switch No.1 condition
OP_SW1
SS_ON_OFF
Off/On
On/off solenoid condition
SS_ON-OFF
TORQUE_DES
Nm
Desired engine torque
TORQUE_DES
APP
%
Accelerator pedal position No.1
APP
G_INHIBIT_6
Off/On
6GR is inhibited due to malfunction.
—
G_INHIBIT_5
Off/On
5GR is inhibited due to malfunction.
—
G_INHIBIT_4
Off/On
4GR is inhibited due to malfunction.
—
G_INHIBIT_3
Off/On
3GR is inhibited due to malfunction.
—
G_INHIBIT_2
Off/On
2GR is inhibited due to malfunction.
—
G_INHIBIT_1
Off/On
1GR is inhibited due to malfunction.
—
G_INHIBIT_R
Off/On
R position is inhibited due to malfunction.
—
G_INHIBIT_N
Off/On
N position is inhibited due to malfunction.
—
OIL_PRES_SW4
Off/On
Oil pressure switch No.4 condition
OP_SW4
OIL_PRES_SW3
Off/On
Oil pressure switch No.3 condition
OP_SW3
EOP_RLY
Off/On
Electric AT oil pump relay condition
EOP_RLY
SHIFT_CTRL
DEFAULT/MANUAL/C_CONTROL/HIGH_TEMP/D_MANUAL/FAIL_SAFE
Shift control mode
SHIFT_CTRL
SLIP_VALUE
RPM
Actual slip value between TSS and OSS
—
HTM_DIS
km {mile}
Travel distance since determination of ATF high temperature mode
HTM_DIS
MST_REC_SFT
—
The gear shift position before shifting gears is displayed.
SE_TYPE
SFT_CTL_STS
—
The shift control execution condition is displayed.
SC_STATE
SERIAL_DTC
—
DTC
—
TR
—
Transaxle range sensor position.
TR
PADDLE_UP
Off/On
Shift up operation using steering shift switch.
PADDLE_UP
PADDLE_DOWN
Off/On
Shift down operation using steering shift switch.
PADDLE_DOWN


Clearing DTCs Procedures

1.  Connect the M-MDS to the DLC-2.

2.  After the vehicle is identified, select the following items from the initialization screen of the M-MDS.

(1)  Select “Self Test”.
(2)  Select “Modules”.
(3)  Select “TCM”.
(4)  Select “Retrieve CMDTCs”.

3.  Verify the DTC according to the directions on the screen.

4.  Press the clear button on the DTC screen to clear the DTC.

5.  Switch the ignition off.

6.  Close all of the doors, bonnet, trunk lid, and liftgate, lock the doors, and wait for 3 min.

7.  Switch the ignition to ON (engine off or on) and wait for 5 s or more.

8.  Perform DTC inspection. (See Reading DTCs Procedure.)

9.  Verify that no DTCs are displayed.