ROAD TEST [FN4A-EL]


id051701290700

Warning
•  When performing a road test, be aware of other vehicles, people, impediments, etc. to avoid an accident.
Note
•  When the legal speed limit must be exceeded, use a chassis dynamometer instead of performing a road test.

Road Test Preparation

1.  Inspect the engine coolant. (See ENGINE COOLANT LEVEL INSPECTION [MZR 1.6].)

2.  Inspect the engine oil. (See ENGINE OIL LEVEL INSPECTION [MZR 1.6].)

3.  Inspect the ATF. (See AUTOMATIC TRANSAXLE FLUID (ATF) INSPECTION [FN4A-EL].)

4.  Inspect the idle speed. (See ENGINE TUNE-UP [MZR 1.6].)

5.  Inspect the ignition timing. (See ENGINE TUNE-UP [MZR 1.6].)

6.  Verify that no DTCs recorded. (See ON-BOARD DIAGNOSTIC SYSTEM DTC INSPECTION [FN4A-EL].)


Shift Diagram (Normal Mode at D Position)

am3zzw00014637

D Position Test

1.  Perform “Road Test Preparation”. (See Road Test Preparation.)

2.  Warm-up the transaxle until the ATF temperature reaches at 60—70 °C.

3.  Select the selector lever to D position.

4.  Perform the road test at D position.

•  If there is any malfunction, perform the “Symptom Troubleshooting”.
(1)  Accelerate the vehicle with half and WOT, then verify that 1GR—2GR, 2GR—3GR, and 3GR—4GR upshifts can be obtained. The shift points must be as shown in the table below.
(2)  Decelerate the vehicle in 4GR, then verify that 4GR—3GR, 3GR—2GR and 2GR—1GR downshifts can be obtained. The shift points must be as shown in the table below.
(3)  Drive the vehicle in 4GR, 3GR, and 2GR and verify that kickdown occurs for 4GR—3GR, 3GR—2GR, 2GR—1GR downshifts, and that the shift points are as shown in the table below.
(4)  Decelerate the vehicle and verify that engine braking effect is felt in 4GR, 3GR and 2GR.
(5)  Drive the vehicle and verify that TCC operation is obtained. The operation points must be as shown in the table below.

Shift point

Position/Mode

Accelerator pedal depressing amount

Shift

Vehicle speed (km/h {mph})

Turbine speed (rpm)

D
NORMAL
WOT
D1→D2
54―60 {34―37}
5,400―5,950
D2→D3
103―111 {64―68}
5,700―6,100
D3→D4
159―169 {99―104}
5,650―5,950
TCC ON (D4)
178―188 {111―116}
4,400―4,600
Half throttle
D1→D2
34―47 {25―29}
3,400―4,700
D2→D3
70―86 {44―53}
3,850―4,750
D3→D4
115―139 {72―86}
4,100―4,900
TCC ON (D4)
145―167 {90―103}
3,600―4,100
CTP
D4→D3
31―37 {20―22}
800―900
D3→D2
8―14 {5―8}
300―450
D2→D1
8―14 {5―8}
450―750
D3→D1
8―14 {5―8}
300―450
Kickdown (WOT)
D4→D3
94—157 {59.0—97.5}
2,350―3,850
D3→D2
46—100 {29.0—62.1}
1,650―3,500
D2→D1
17—50 {11—31}
950―2,700
POWER
WOT
D1→D2
54―60 {34―37}
5,400―5,950
D2→D3
103―111 {64―68}
5,700―6,100
D3→D4
159―169 {99―104}
5,650―5,950
Half throttle
D1→D2
42―50 {27―31}
4,200―4,950
D2→D3
81―97 {51―60}
4,500―5,300
D3→D4
150―168 {93―104}
5,350―5,900
CTP
D4→D3
31―37 {20―22}
800―900
D3→D2
8―14 {5―8}
300―450
D2→D1
8―14 {5―8}
450―750
D3→D1
8―14 {5―8}
300―450
Kickdown (WOT)
D4→D3
147―157 {92―97}
3,650―3,850
D3→D2
92―100 {58―62}
3,300―3,500
D2→D1
44―50 {28―31}
2,450―2,700


M Position Test

1.  Perform “Road Test Preparation”. (See Road Test Preparation.)

2.  Warm-up the transaxle until the ATF temperature reaches at 60—70 °C.

3.  Select the selector lever to M position.

4.  Perform the road test at M position.

•  If there is any malfunction, perform the “Symptom Troubleshooting”.
(1)  Verify that upshifts and downshifts are obtained by manual shifting of the selector lever forward and back.
(2)  Decelerate the vehicle in 4GR, then verify that 4GR—3GR, 3GR—2GR and 2GR—1GR downshifts can be obtained. The shift points must be as shown in the table below.
(3)  Decelerate the vehicle and verify that engine braking effect is felt in all gear position.

Shift point

Position/Mode

Accelerator pedal depressing amount

Shift

Vehicle speed (km/h {mph})

Turbine speed (rpm)

M
NORMAL
CTP
M4→M3
31―37 {20―22}
800―900
M3→M2
8―14 {5―8}
300―450
M2→M1
8―14 {5―8}
450―750
M3→M1
8―14 {5―8}
300―450


P Position Test

1.  Select the selector lever to P position on a gentle slope.

2.  Release the brake and verify that the vehicle does not roll.

•  If the vehicle rolls, inspect the parking mechanism in the transaxle.