DTC P0506:00 [MZR 1.6]

DTC P0506:00	IAC system RPM lower than expected
DETECTION CONDITION	• The actual idle speed is lower than expected by 100 rpm for 14 s when the brake pedal is depressed (brake switch is on). Note • If the atmospheric pressure is less than 72.2 kPa {0.736 kgf/cm², 10.5 psi} or the intake air temperature is below −10 °C {14 °F}, the PCM cancels the diagnosis of DTC P0506:00. Diagnostic support note • This is a continuous monitor (CCM). • The check engine light illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM. • PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • DTC is stored in the PCM memory.
POSSIBLE CAUSE	• A/C relay control circuit malfunction • Drive-by-wire control system related sensor malfunction • Purge solenoid valve malfunction • Air cleaner element clogged • Air intake passage clogged • Low engine compression (Over capacity of blow-by gas) • Generator malfunction • PCM malfunction

DTC P0506:00

IAC system RPM lower than expected

DETECTION CONDITION

• The actual idle speed is lower than expected by 100 rpm for 14 s when the brake pedal is depressed (brake switch is on).

Note

• If the atmospheric pressure is less than 72.2 kPa {0.736 kgf/cm², 10.5 psi} or the intake air temperature is below −10 °C {14 °F}, the PCM cancels the diagnosis of DTC P0506:00.

Diagnostic support note

• This is a continuous monitor (CCM).

• The check engine light illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.

• PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle.

• FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

• DTC is stored in the PCM memory.

POSSIBLE CAUSE

• A/C relay control circuit malfunction

• Drive-by-wire control system related sensor malfunction

• Purge solenoid valve malfunction

• Air cleaner element clogged

• Air intake passage clogged

• Low engine compression (Over capacity of blow-by gas)

• Generator malfunction

• PCM malfunction

STEP	INSPECTION	ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
No	Go to the next step.
3	VERIFY RELATED PENDING CODE AND STORED DTC • Switch the ignition off, then ON (engine off). • Verify the related PENDING CODE and stored DTCs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].) • Are any other DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [MZR 1.6].)
No	Go to the next step.
4	INSPECT A/C MAGNETIC CLUTCH OPERATION • Turn the blower motor switch off. • Is the magnetic clutch still on?	Yes	Perform the symptom troubleshooting “NO.24 A/C IS ALWAYS ON OR A/C COMPRESSOR RUNS CONTINUOUSLY”. (See NO.24 A/C IS ALWAYS ON OR A/C COMPRESSOR RUNS CONTINUOUSLY [MZR 1.6].)
No	Go to the next step.
5	INSPECT DRIVE-BY-WIRE CONTROL SYSTEM RELATED SENSOR • Inspect the following parts: ― APP sensor (See ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION [MZR 1.6].) ― TP sensor (See THROTTLE POSITION (TP) SENSOR INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Repair or replace the malfunctioning part according to the inspection results, then go to Step 11. (See ACCELERATOR PEDAL REMOVAL/INSTALLATION [MZR 1.6].) (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZR 1.6].)
No	Go to the next step.
6	INSPECT PURGE SOLENOID VALVE • Inspect the purge solenoid valve. (See PURGE SOLENOID VALVE INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Replace the purge solenoid valve, then go to Step 11. (See PURGE SOLENOID VALVE REMOVAL/INSTALLATION [MZR 1.6].)
No	Go to the next step.
7	INSPECT AIR CLEANER ELEMENT • Remove the air cleaner element with the engine running. • Does the engine speed increase?	Yes	Clean or replace the air cleaner element, then go to Step 11.
No	Go to the next step.
8	INSPECT THROTTLE BODY PASSAGE • Visually inspect the throttle body passage. • Is the throttle body clogged?	Yes	Clean or replace the throttle body passage, then go to Step 11. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZR 1.6].)
No	Go to the next step.
9	INSPECT ENGINE COMPRESSION • Inspect the engine compression. (See COMPRESSION INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 11.
No	Go to the next step.
10	INSPECT GENERATOR • Inspect the generator. (See GENERATOR INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Replace the generator, then go to the next step. (See GENERATOR REMOVAL/INSTALLATION [MZR 1.6].)
No	Go to the next step.
11	VERIFY DTC TROUBLESHOOTING COMPLETED • Always reconnect all disconnected connectors. • Start the engine. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [MZR 1.6].) • Depress the brake pedal for 14 s or more. • Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].) • Is the PENDING CODE for this DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [MZR 1.6].) Go to the next step.
No	Go to the next step.
12	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [MZR 1.6].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [MZR 1.6].)
No	DTC troubleshooting completed.

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED

• Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?

Yes

Go to the next step.

Record the FREEZE FRAME DATA (Mode 2)/snapshot data on repair order, then go to the next step.

VERIFY RELATED SERVICE INFORMATION AVAILABILITY

• Verify related Service Information availability.

• Is any related Service Information available?

Yes

Perform repair or diagnosis according to the available Service Information.

• If the vehicle is not repaired, go to the next step.

Go to the next step.

VERIFY RELATED PENDING CODE AND STORED DTC

• Switch the ignition off, then ON (engine off).

• Verify the related PENDING CODE and stored DTCs using the M-MDS.

(See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].)

• Are any other DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [MZR 1.6].)

Go to the next step.

INSPECT A/C MAGNETIC CLUTCH OPERATION

• Turn the blower motor switch off.

• Is the magnetic clutch still on?

Yes

Perform the symptom troubleshooting “NO.24 A/C IS ALWAYS ON OR A/C COMPRESSOR RUNS CONTINUOUSLY”.

(See NO.24 A/C IS ALWAYS ON OR A/C COMPRESSOR RUNS CONTINUOUSLY [MZR 1.6].)

Go to the next step.

INSPECT DRIVE-BY-WIRE CONTROL SYSTEM RELATED SENSOR

• Inspect the following parts:

― APP sensor

(See ACCELERATOR PEDAL POSITION (APP) SENSOR INSPECTION [MZR 1.6].)

― TP sensor

(See THROTTLE POSITION (TP) SENSOR INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Repair or replace the malfunctioning part according to the inspection results, then go to Step 11.

(See ACCELERATOR PEDAL REMOVAL/INSTALLATION [MZR 1.6].)

(See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

INSPECT PURGE SOLENOID VALVE

• Inspect the purge solenoid valve.

(See PURGE SOLENOID VALVE INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Replace the purge solenoid valve, then go to Step 11.

(See PURGE SOLENOID VALVE REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

INSPECT AIR CLEANER ELEMENT

• Remove the air cleaner element with the engine running.

• Does the engine speed increase?

Yes

Clean or replace the air cleaner element, then go to Step 11.

Go to the next step.

INSPECT THROTTLE BODY PASSAGE

• Visually inspect the throttle body passage.

• Is the throttle body clogged?

Yes

Clean or replace the throttle body passage, then go to Step 11.

(See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

INSPECT ENGINE COMPRESSION

• Inspect the engine compression.

(See COMPRESSION INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Repair or replace the malfunctioning parts according to the inspection results, then go to Step 11.

Go to the next step.

INSPECT GENERATOR

• Inspect the generator.

(See GENERATOR INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Replace the generator, then go to the next step.

(See GENERATOR REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

VERIFY DTC TROUBLESHOOTING COMPLETED

• Always reconnect all disconnected connectors.

• Start the engine.

• Clear the DTC from the PCM memory using the M-MDS.

(See AFTER REPAIR PROCEDURE [MZR 1.6].)

• Depress the brake pedal for 14 s or more.

• Perform the Pending Trouble Code Access Procedure.

(See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].)

• Is the PENDING CODE for this DTC present?

Yes

Repeat the inspection from Step 1.

• If the malfunction recurs, replace the PCM.

(See PCM REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

• Perform the “AFTER REPAIR PROCEDURE”.

(See AFTER REPAIR PROCEDURE [MZR 1.6].)

• Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [MZR 1.6].)

DTC troubleshooting completed.