DTC P059F:00 [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5]

id0102h9402100

DTC P059F:00

Active air shutter: Opening angle abnormality (spinning free)

DETECTION CONDITION

•  Active air shutter opening angle is certain value or more.

Diagnostic support note

•  This is a continuous monitor (other).

•  The check engine light does not illuminate.

•  PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle.

•  FREEZE FRAME DATA (Mode 2) is not available.

•  Snapshot data is available.

•  DTC is stored in the PCM memory.

FAIL-SAFE FUNCTION

•  Performs fully open/closed position learning function three times.

POSSIBLE CAUSE

•  Active air shutter malfunction

•  PCM malfunction

SYSTEM WIRING DIAGRAM

Not applicable

DTC P059F:00	Active air shutter: Opening angle abnormality (spinning free)
DETECTION CONDITION	• Active air shutter opening angle is certain value or more. Diagnostic support note • This is a continuous monitor (other). • The check engine light does not illuminate. • PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle. • FREEZE FRAME DATA (Mode 2) is not available. • Snapshot data is available. • DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION	• Performs fully open/closed position learning function three times.
POSSIBLE CAUSE	• Active air shutter malfunction • PCM malfunction
SYSTEM WIRING DIAGRAM	Not applicable

Diagnostic Procedure

STEP	INSPECTION		ACTION
1	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED • Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?	Yes	Go to the next step.
1		No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
2	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
2		No	Go to the next step.
3	VERIFY IF DIAGNOSTIC RESULT IS AFFECTED BY DTC RELATED TO ACTIVE AIR SHUTTER • Switch the ignition off, then ON (engine off). • Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) • Is the PENDING CODE/DTC U0284:00 also present?	Yes	Go to the applicable PENDING CODE or DTC inspection. (See DTC U0284:00 [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
3		No	Go to the next step.
4	INSPECT ACTIVE AIR SHUTTER • Inspect the active air shutter. (See ACTIVE AIR SHUTTER INSPECTION.) • Is there any malfunction?	Yes	Replace the active air shutter, then go to the next step. (See ACTIVE AIR SHUTTER REMOVAL/INSTALLATION.)
4		No	Go to the next step.
5	VERIFY DTC TROUBLESHOOTING COMPLETED • Always reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) • Start the engine. • Drive the vehicle at 10 km/h {6.2 mph} or more for approx. 1 min. • Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) • Is the PENDING CODE and/or DTC for this DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) Go to the next step.
5		No	Go to the next step.
6	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
6		No	DTC troubleshooting completed.