DTC P0219:00 [SKYACTIV-D 1.5]

id0102q2148300

DTC P0219:00

Engine overspeed condition
DETECTION CONDITION
•  PCM detects that the engine speed is 5,670 rpm or more.
Diagnostic support note
•  This is an intermittent monitor (other).
•  The check engine light does not illuminate.
•  FREEZE FRAME DATA is not available.
•  Snapshot data is available.
•  DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION
Not applicable
POSSIBLE CAUSE
•  ATX system malfunction (ATX)
―  Excessive rotation due to improper gear lock
•  Malfunction caused by the following driving operations:
―  Excessive rotation due to improper shift operation
―  Deceleration using improper gear, and descending slope
•  Mechanical (engine) malfunction
―  Fuel injector malfunction
•  PCM malfunction
SYSTEM WIRING DIAGRAM
Not applicable

Diagnostic Procedure

STEP

INSPECTION

ACTION
1
RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
Note
•  Recording can be facilitated using the screen capture function of the PC.
•  Record the snapshot data on the repair order.
—
Go to the next step.
2
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY RELATED PENDING CODE AND/OR DTC
•  Switch the ignition off, then ON (engine off).
•  Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
•  Is the PENDING CODE/DTC P0336:00 or P0337:00 also present?
Yes
Go to the applicable PENDING CODE or DTC inspection.
(See DTC P0336:00 [SKYACTIV-D 1.5].)
(See DTC P0337:00 [SKYACTIV-D 1.5].)
No
Go to the next step.
4
VERIFY DTC RELATED FUEL SYSTEM PART
•  Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
•  Is a DTC related to a fuel system part stored?
Yes
Go to the applicable PENDING CODE or DTC inspection.
(See DTC TABLE [SKYACTIV-D 1.5].)
No
ATX:
•  Go to the next step.
MTX:
•  Go to Step 6.
5
VERIFY ATX RELATED DTC
•  Retrieve TCM DTCs using the M-MDS.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See ON-BOARD DIAGNOSTIC SYSTEM DTC TABLE [EW6A-EL].)
No
Go to the next step.
6
INSPECT EFFECT OF VEHICLE CONDITION FOR MALFUNCTION
•  Verify how the customer drives the vehicle by asking the customer the following:
―  Improper shift operation
―  Deceleration using improper gear, and descending slope
•  Is the use situation as indicated above?
Yes
Explain to the customer that the vehicle is normal. (malfunction due to customer’s improper driving operation)
If there is a concern with customer’s driving, provide the customer some pertinent advice (such as gear selection, how to use manual mode).
No
Go to the next step.
7
INSPECT FUEL INJECTOR OPERATION
•  Perform the Fuel Injector Operation Inspection.
•  Is there any malfunction?
Yes
Repair or replace the malfunctioning part according to the inspection results, then go to the next step.
(See FUEL INJECTOR REMOVAL/INSTALLATION [SKYACTIV-D 1.5].)
No
Go to the next step.
8
VERIFY DTC TROUBLESHOOTING COMPLETED
•  Always reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Start the engine and warm it up completely.
•  Drive the vehicle.
•  Perform the DTC Reading Procedure.
•  Is the same DTC present?
Yes
Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 1.5].)
No
Go to the next step.
9
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [SKYACTIV-D 1.5].)
No
DTC troubleshooting completed.