DTC P117A:00 [SKYACTIV-D 1.5]
id0102q2316900
DTC P117A:00 |
Record of torque restriction for piston protection |
---|---|
DETECTION CONDITION
|
• The engine oil pressure is the specified value or less for a continuous 15 s.
• The vehicle is driven continuously for a certain period of time at low engine speed and high load.
Diagnostic support note
• This is an intermittent monitor (other).
• The check engine light does not illuminate.
• FREEZE FRAME DATA is not available.
• Snapshot data is available.
• DTC is stored in the PCM memory.
|
FAIL-SAFE FUNCTION
|
Not applicable
|
POSSIBLE CAUSE
|
• Engine oil pressure is low.
• Engine oil temperature is high.
• High engine speed condition is continued with the engine oil diluted.
• Vehicle is driven continuously at low engine speed and high load
• Engine oil pressure sensor malfunction
• PCM malfunction
|
SYSTEM WIRING DIAGRAM
|
Not applicable
|
Diagnostic Procedure
STEP |
INSPECTION |
ACTION |
|
---|---|---|---|
1
|
RECORD VEHICLE STATUS AT TIME OF DTC DETECTION TO UTILIZE WITH REPEATABILITY VERIFICATION
• Record the snapshot data on the repair order.
|
—
|
Go to the next step.
|
2
|
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
• Verify related Service Information availability.
• Is any related Service Information available?
|
Yes
|
Perform repair or diagnosis according to the available Service Information.
• If the vehicle is not repaired, go to the next step.
|
No
|
Go to the next step.
|
||
3
|
VERIFY RELATED PENDING CODE AND/OR DTC
• Switch the ignition off, then ON (engine off).
• Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
• Are any other PENDING CODEs and/or DTCs present?
|
Yes
|
Go to the applicable PENDING CODE or DTC inspection.
(See DTC TABLE [SKYACTIV-D 1.5].)
|
No
|
Go to the next step.
|
||
4
|
INSPECT EFFECT OF VEHICLE CONDITION FOR MALFUNCTION
• Verify how the customer drives the vehicle by asking the customer the following:
• Are any of the conditions above applicable to the vehicle use conditions?
|
Yes
|
Explain to the customer that the vehicle is normal. (malfunction caused by driving at high engine speed with engine oil diluted)
If there is a concern with customer’s driving, provide the customer some pertinent advice (such as gear selection, how to use manual mode).
Go to Step 7.
|
No
|
Go to the next step.
|
||
5
|
INSPECT ENGINE OIL LEAKAGE
• Start the engine.
• Visually inspect the engine oil runner for engine oil leakage.
• Is there any leakage?
|
Yes
|
Repair or replace the malfunctioning part according to the inspection results, then add genuine motor oil.
Perform the “ENGINE OIL DATA RESET”, then go to Step 7.
|
No
|
Go to the next step.
|
||
6
|
INSPECT ENGINE OIL PRESSURE SENSOR
• Inspect the engine oil pressure sensor.
• Is there any malfunction?
|
Yes
|
Replace the engine oil temperature sensor/engine oil pressure sensor, then go to the next step.
|
No
|
Go to the next step.
|
||
7
|
VERIFY DTC TROUBLESHOOTING COMPLETED
• Always reconnect all disconnected connectors.
• Clear the DTC from the PCM memory using the M-MDS.
• Start the engine and warm it up completely.
• Drive the vehicle.
• Perform the DTC Reading Procedure.
• Is the same DTC present?
|
Yes
|
Repeat the inspection from Step 1.
• If the malfunction recurs, replace the PCM.
Go to the next step.
|
No
|
Go to the next step.
|
||
8
|
VERIFY AFTER REPAIR PROCEDURE
• Perform the “AFTER REPAIR PROCEDURE”.
• Are any DTCs present?
|
Yes
|
Go to the applicable DTC inspection.
(See DTC TABLE [SKYACTIV-D 1.5].)
|
No
|
DTC troubleshooting completed.
|