DTC P117A:00 [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5]

id0102h9316900

DTC P117A:00

Engine oil temperature is high
DETECTION CONDITION
•  Any one of the following conditions is met:
―  With the transmission in 5th gear or lower gear, an engine speed of 6,100 rpm (SKYACTIV-G 1.5, SKYACTIV-G 2.0)/5,800 rpm (SKYACTIV-G 2.5) or more continues for 6 min.
―  The estimated engine oil temperature exceeds 140 °C {284 °F} continues for 6 min (with active air shutter).
Diagnostic support note
•  This is a continuous monitor (other).
•  The check engine light does not illuminate.
•  FREEZE FRAME DATA (Mode 2) is not available.
•  Snapshot data is available.
•  DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION
•  Limits intake air amount
POSSIBLE CAUSE
•  High engine speed condition continues
•  Active air shutter close malfunction (with active air shutter)
•  PCM malfunction
SYSTEM WIRING DIAGRAM
Not applicable

Diagnostic Procedure

STEP

INSPECTION

ACTION
1
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
2
VERIFY RELATED PENDING CODE AND/OR DTC
•  Switch the ignition off, then ON (engine off).
•  Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
•  Is the PENDING CODE/DTC P0335:00, P059F:00, P05A0:00, P05A3:00, P05C0:00 or U0284:00 also present?
Yes
Go to the applicable PENDING CODE or DTC inspection.
(See DTC P0335:00 [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
(See DTC P059F:00 [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
(See DTC P05A0:00 [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
(See DTC P05A3:00 [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
(See DTC P05C0:00 [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
(See DTC U0284:00 [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
No
Go to the next step.
3
INSPECT EFFECT OF VEHICLE CONDITION FOR MALFUNCTION
•  Verify how the customer drives the vehicle by asking the customer the following:
•  Does the engine speed exceed 6,100 rpm (SKYACTIV-G 1.5, SKYACTIV-G 2.0)/5,800 rpm (SKYACTIV-G 2.5) for 6 min or more while driving in 5th gear or lower gear?
Yes
Explain to the customer that the vehicle is normal. (malfunction caused by continuous engine speed exceeding 6,100 rpm (SKYACTIV-G 1.5, SKYACTIV-G 2.0)/5,800 rpm (SKYACTIV-G 2.5) for 6 min or more while in 5th gear or lower gear)
If there is a concern with customer’s driving, provide the customer some pertinent advice (such as gear selection, how to use manual mode).
Go to the next step.
No
Go to the next step.
4
VERIFY DTC TROUBLESHOOTING COMPLETED
•  Always reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Start the engine and warm it up completely.
•  Drive the vehicle.
•  Perform the DTC Reading Procedure.
•  Is the same DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the PCM.
Go to the next step.
No
Go to the next step.
5
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].)
No
DTC troubleshooting completed.