DTC P1282:00 [SKYACTIV-D 2.2]

id0102s4214200

DTC P1282:00

Common rail control system problem
DETECTION CONDITION
•  When the following conditions are met, the common rail fuel pressure value exceeds 250 MPa {2,549 kgf/cm2, 36,260 psi} or the fuel pressure value exceeds the value calculated by the PCM based on the engine speed for a continuous 1 s.
MONITORING CONDITIONS
―  Battery voltage: 8 V or more
―  0.5 s have elapsed after the ignition was switched ON (engine on)
―  Engine speed: above 500 rpm
―  The following DTCs are not detected:
•  Fuel pressure sensor: P0191:00, P0192:00, P0193:00
Diagnostic support note
•  This is an intermittent monitor (fuel system).
•  The check engine light illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.
•  PENDING CODE is available if the PCM detects the above malfunction condition during first drive cycle.
•  FREEZE FRAME DATA (Mode 2)/Snapshot data is available.
•  DTC is stored in the PCM memory.
FAIL-SAFE FUNCTION
•  PCM restricts engine torque.
•  Increase the idle speed.
•  Inhibits the diesel particulate filter regeneration control.
•  Inhibits engine-stop by operating the i-stop function.
POSSIBLE CAUSE
•  Fuel pressure relief valve malfunction
•  Fuel pressure sensor malfunction
•  Suction control valve malfunction
•  Fuel pipe perforation or breakage (poor contact)
•  Fuel filter clogged (The PCM corrects the fuel pressure in the direction of increase via feedback control in response to a fuel pressure decrease due to temporary clogging. If the clogging is cleared, a DTC is detected because fuel pressure increases to the threshold or more.)
•  PCM malfunction
SYSTEM WIRING DIAGRAM
Not applicable

Diagnostic Procedure

STEP

INSPECTION

ACTION
1
VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA HAS BEEN RECORDED
•  Has the FREEZE FRAME DATA (Mode 2)/snapshot data been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA (Mode 2)/snapshot data on the repair order, then go to the next step.
2
VERIFY RELATED SERVICE INFORMATION AVAILABILITY
•  Verify related Service Information availability.
•  Is any related Service Information available?
Yes
Perform repair or diagnosis according to the available Service Information.
•  If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY RELATED PENDING CODE AND/OR DTC
•  Switch the ignition off, then ON (engine off).
•  Perform the Pending Trouble Code Access Procedure and DTC Reading Procedure.
•  Are any other PENDING CODEs and/or DTCs present?
Yes
Go to the applicable PENDING CODE or DTC inspection.
(See DTC TABLE [SKYACTIV-D 2.2].)
No
Go to the next step.
4
VERIFY CURRENT INPUT SIGNAL STATUS IS CONCERN INTERMITTENT OR CONSTANT
•  Clear the DTC from the PCM memory using the M-MDS.
•  Start the engine.
•  Perform the Pending Trouble Code Access Procedure.
•  Is the PENDING CODE for this DTC present?
Yes
Go to the next step.
No
Intermittent concern exists.
•  Perform the “INTERMITTENT CONCERN TROUBLESHOOTING” procedure.
5
INSPECT FUEL PRESSURE RELIEF VALVE
•  Inspect the fuel pressure relief valve.
•  Is there any malfunction?
Yes
Replace the common rail, then go to Step 10.
(See COMMON RAIL REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
No
Go to the next step.
6
INSPECT FUEL PRESSURE SENSOR
•  Inspect the fuel pressure sensor.
•  Is there any malfunction?
Yes
Replace the common rail, then go to Step 10.
(See COMMON RAIL REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
No
Go to the next step.
7
INSPECT SUCTION CONTROL VALVE
•  Inspect the suction control valve.
•  Is there any malfunction?
Yes
Replace the suction control valve, then go to Step 10.
(See SUCTION CONTROL VALVE REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
No
Go to the next step.
8
INSPECT FUEL LINE
•  Inspect the fuel line.
•  Is there any malfunction?
Yes
Repair or replace the malfunctioning part according to the inspection results, then go to Step 10.
No
Go to the next step.
9
INSPECT FUEL FILTER FOR CLOGGING
•  Visually inspect the fuel filter.
•  Is there any malfunction?
Yes
Repair or replace the malfunctioning part according to the inspection results, then go to the next step.
(See FUEL FILTER REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)
No
Go to the next step.
10
VERIFY DTC TROUBLESHOOTING COMPLETED
•  Always reconnect all disconnected connectors.
•  Clear the DTC from the PCM memory using the M-MDS.
•  Start the engine and warm it up completely.
Caution
•  While performing this step, always operate the vehicle in a safe and lawful manner.
•  When the M-MDS is used to observe monitor system status while driving, be sure to have another technician with you, or record the data in the M-MDS using the PID/DATA MONITOR AND RECORD capturing function and inspect later.
•  Drive the vehicle under the FREEZE FRAME DATA (Mode 2)/snapshot data condition.
•  Perform the Pending Trouble Code Access Procedure.
•  Is the PENDING CODE for this DTC present?
Yes
Repeat the inspection from Step 1.
•  If the malfunction recurs, replace the PCM.
Go to the next step.
No
Go to the next step.
11
VERIFY AFTER REPAIR PROCEDURE
•  Perform the “AFTER REPAIR PROCEDURE”.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
(See DTC TABLE [SKYACTIV-D 2.2].)
No
DTC troubleshooting completed.