NO.10 HARD TO START/LONG CRANK/ERRATIC START/ERRATIC CRANK [SKYACTIV-D 1.5]


id0103q2897700

10

HARD TO START/LONG CRANK/ERRATIC START/ERRATIC CRANK

DESCRIPTION
•  There is ignition, but the engine does not run under its own power.
•  Long period of time required before the engine starts.
POSSIBLE CAUSE
Note
•  If the ignition is not switched off (to LOCK or ACC) after the engine stalls, and then an engine restart is attempted, the PCM corrects the difference between CKP sensor and CMP sensor signals caused by engine stalling, which may result in more time needed to restart the engine.
•  PCM DTC is stored.
•  A/C relay malfunction
•  ECT sensor malfunction
•  Fuel injection system malfunction
―  Fuel leakage from fuel system
―  Air suction in fuel system
―  Common rail malfunction
―  Supply pump malfunction
―  Suction control valve malfunction
―  Fuel injector malfunction
―  Fuel pressure relief valve malfunction
•  Poor fuel quality
•  Mechanical (engine) malfunction
―  Large mechanical resistance
―  Improper engine compression
―  Improper valve timing
―  Engine oil malfunction (oil working up or down)
Warning
•  The following troubleshooting flow chart contains the fuel system diagnosis and repair procedures. Read the following warnings before performing the fuel system services:
―  Always keep sparks and flames away from fuel. Fuel can be easily ignited which could cause serious injury or death, and damage to equipment.
―  Fuel line spills and leakage from the pressurized fuel system are dangerous. Fuel can ignite and cause serious injury or death, and damage to property and facilities. Fuel can also irritate skin and eyes. To prevent this, always complete the "Fuel Line Safety Procedure", while referring to the "BEFORE SERVICE PRECAUTION". (See BEFORE SERVICE PRECAUTION [SKYACTIV-D 1.5].)
―  Fuel is highly flammable and dangerous. Fuel line spills and leakage can cause serious injury or death, and damage to equipment. When installing the fuel hose, always refer to the "AFTER SERVICE PRECAUTION" and perform the "Fuel Hose Installation Procedure". (See AFTER SERVICE PRECAUTION [SKYACTIV-D 1.5].)


Diagnostic Procedure

STEP

INSPECTION

RESULTS

ACTION

1
VERIFY PCM DTC
•  Retrieve PCM DTCs using the M-MDS.
•  Are any DTCs present?
Yes
Go to the applicable DTC inspection.
No
Go to the next step.
2
INSPECT A/C RELAY
•  Switch the ignition off.
•  Remove the A/C relay.
•  Inspect the A/C relay.
•  Is the A/C relay normal?
Yes
Go to the next step.
No
Replace the A/C relay, then go to Step 11.
3
INSPECT ECT SENSOR
•  Is the ECT sensor normal?
Yes
Go to the next step.
No
Replace the ECT sensor, then go to Step 11.
4
INSPECT FOR FUEL LEAKAGE OR AIR SUCTION IN FUEL SYSTEM
•  Visually inspect the following:
―  Fuel leakage from the fuel tank, fuel pump, hose, pipe, fuel injector, supply pump, common rail
―  Cracking and damage in fuel hose and pipe
―  Clamp installation condition for each hose and pipe
―  Fuel pipe securing condition due to deterioration such as rubber of clamp
•  Are all items normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning part according to the inspection results, then go to Step 11.
5
INSPECT FUEL INJECTION RELATED PARTS
•  Inspect the following parts:
―  Common rail
―  Supply pump
―  Suction control valve
―  Fuel injector
―  Fuel pressure relief valve
•  Are all items normal?
Yes
Go to the next step.
No
Repair or replace the malfunctioning part according to the inspection results, then go to Step 11.
6
INSPECT FOR MALFUNCTION DUE TO POOR FUEL
•  Replace the fuel.
•  Does the symptom disappear?
Yes
Advise the customer as to the change in the fuel used.
No
Remove the accumulated matter in the cylinder head using the following procedure, then go to the next step.
•  Carbon remover
•  Overhauling
7
DETERMINE IF MALFUNCTION IS DUE TO EXCESSIVE ENGINE SPEED RESISTANCE
•  Rotate the crankshaft pulley lock bolt clockwise using a wrench.
•  Can bolts be rotated?
Yes
Go to Step 9.
No
Go to the next step.
8
INSPECT FOR MALFUNCTION DUE TO EXCESSIVE MECHANICAL RESISTANCE OF ENGINE ACCESSORIES
•  Remove all drive belts from engine accessories.
Caution
•  Do not run the engine for long periods with the drive belts of engine accessories removed. Otherwise the engine could be damaged from overheating.
•  Start the engine.
•  Is cranking possible? (Does the engine start?)
Yes
Repair or replace the malfunctioning part according to the inspection results, then go to Step 11. (Large mechanical resistance in engine accessories.)
No
Go to the next step.
9
INSPECT ENGINE COMPRESSION
•  Inspect the engine compression.
•  Are compression pressures within specification?
Yes
Go to Step 11.
No
Go to the next step.
10
INSPECT FOR MALFUNCTION DUE TO DEVIATED VALVE TIMING
•  Inspect the valve timing (timing chain installation condition).
•  Is the valve timing normal?
Yes
Inspect for the following engine internal parts:
•  Cylinder
•  Piston ring
•  Intake valve
•  Exhaust valve
•  Such as cylinder head gasket
Repair or replace the malfunctioning part according to the inspection results, then go to the next step.
No
Adjust the valve timing to the correct timing, then go to the next step.
11
Verify the test results.
•  If normal, return to the diagnostic index to service any additional symptoms.
•  If a malfunction remains, inspect the related Service Information and perform the repair or diagnosis.
―  If the vehicle is repaired, troubleshooting is completed.
―  If the vehicle is not repaired or additional diagnostic information is not available, replace the PCM.