EXHAUST GAS TEMPERATURE SENSOR INSPECTION [SKYACTIV-D 2.2]


id0140z7446300


Exhaust Gas Temperature Sensor No.1

Warning
•  A hot engine and exhaust system can cause severe burns. Turn off the engine and wait until they are cool before removing the exhaust system.
Caution
•  Perform exhaust gas temperature sensor removal/installation only when inspection or replacement is required, such as when DTCs for the sensor are displayed, because it may cause exhaust gas leaks.
•  If removal or installation/removal is performed, always verify that there is no exhaust gas leak after reinstallation.

Resistance inspection

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

2.  Remove the battery. (See BATTERY REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

3.  Remove the air inlet pipe, air hose and turbocharger air inlet hose. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

4.  Disconnect the exhaust gas temperature sensor No.1 connector.

5.  Remove the clip A from the bracket. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

6.  Remove the clip B from the bracket. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

7.  Remove the exhaust gas temperature sensor No.1. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

8.  Place the exhaust gas temperature sensor No.1 in water with a thermometer, and heat the water gradually.

ac5wzw00004438

9.  Measure the resistance between exhaust gas temperature sensor No.1 terminals A and B.

•  If not as specified, replace the exhaust gas temperature sensor No.1. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

Specification (Reference)

Water temperature (°C {°F})

Resistance (Kilohms)

100 {212}
Approx. 4.51

am3zzw00013586


Exhaust Gas Temperature Sensor No.2

Warning
•  A hot engine and exhaust system can cause severe burns. Turn off the engine and wait until they are cool before removing the exhaust system.
Caution
•  Perform exhaust gas temperature sensor removal/installation only when inspection or replacement is required, such as when DTCs for the sensor are displayed, because it may cause exhaust gas leaks.
•  If removal or installation/removal is performed, always verify that there is no exhaust gas leak after reinstallation.

Resistance inspection

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

2.  Remove the engine cover. (See ENGINE COVER REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

3.  Remove the insulator. (See TIMING CHAIN REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

4.  Disconnect the exhaust gas temperature sensor No.2 connector.

5.  Remove the exhaust gas temperature sensor No.2. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

6.  Place the exhaust gas temperature sensor No.2 in water with a thermometer, and heat the water gradually.

ac5wzw00004436

7.  Measure the resistance between exhaust gas temperature sensor No.2 terminals A and B.

•  If not as specified, replace the exhaust gas temperature sensor No.2. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

Specification (Reference)

Water temperature (°C {°F})

Resistance (Kilohms)

50 {122}
Approx. 106

am3zzw00013587


Exhaust Gas Temperature Sensor No.3

Warning
•  A hot engine and exhaust system can cause severe burns. Turn off the engine and wait until they are cool before removing the exhaust system.
Caution
•  Do not allow flammable objects such as the taping for bundling wiring harness to come into contact with the catalytic converter.
•  Perform exhaust gas temperature sensor removal/installation only when inspection or replacement is required, such as when DTCs for the sensor are displayed, because it may cause exhaust gas leaks.
•  If removal or installation/removal is performed, always verify that there is no exhaust gas leak after reinstallation.

Resistance inspection

1.  Turn the steering wheel to full right lock.

2.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)

3.  Lift up the vehicle.

4.  Remove the front splash shield (RH). (See SPLASH SHIELD REMOVAL/INSTALLATION.)

5.  Remove the plate (exhaust system). (See EXHAUST SYSTEM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

6.  Disconnect the exhaust gas temperature sensor No.3 connector.

7.  Remove the clip from the bracket. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

8.  Remove the wiring harness from the wire clip A and B. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

9.  Remove the exhaust gas temperature sensor No.3. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

10.  Place the exhaust gas temperature sensor No.3 in water with a thermometer, and heat the water gradually.

ac5wzw00004440

11.  Measure the resistance between exhaust gas temperature sensor No.3 terminals A and B.

•  If not as specified, replace the exhaust gas temperature sensor No.3. (See EXHAUST GAS TEMPERATURE SENSOR REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

Specification (Reference)

Water temperature (°C {°F})

Resistance (Kilohms)

50 {122}
Approx. 106

am3zzw00013588