DTC P0171:00 [MZR 1.6]

DTC P0171:00	Fuel trim system too lean
DETECTION CONDITION	• The PCM monitors short term fuel trim (SHRTFT) and long term fuel trim (LONGFT) values when closed loop fuel control. If the LONGFT and the sum total of these fuel trims exceed preprogrammed criteria, the PCM determines that the fuel system is too lean. Diagnostic support note • This is a continuous monitor (fuel system). • The check engine light illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM. • PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle. • FREEZE FRAME DATA (Mode 2)/Snapshot data is available. • DTC is stored in the PCM memory.
POSSIBLE CAUSE	• Misfire • Erratic signal to PCM ― APP sensor signal malfunction ― ECT sensor signal malfunction ― MAF sensor signal malfunction ― TP sensor signal malfunction ― VSS signal malfunction • A/F sensor heater malfunction • A/F sensor malfunction ― Looseness A/F sensor ― A/F sensor deterioration • Leakage exhaust system • Air suction in intake air system • MAF sensor malfunction • Improper operation of purge control system • Fuel supply system malfunction ― Pressure regulator malfunction ― Fuel pump unit malfunction ― Fuel leakage on fuel line from fuel distributor and fuel pump ― Fuel filter clogged or restricted ― Fuel return hose clogged • Ignition system malfunction ― Ignition coil related wiring harness malfunction ― Spark plug malfunction ― Ignition coil malfunction • Improper operation of variable valve timing control system • Insufficient engine compression • Improper operation of fuel injector • PCM malfunction

DTC P0171:00

Fuel trim system too lean

DETECTION CONDITION

• The PCM monitors short term fuel trim (SHRTFT) and long term fuel trim (LONGFT) values when closed loop fuel control. If the LONGFT and the sum total of these fuel trims exceed preprogrammed criteria, the PCM determines that the fuel system is too lean.

Diagnostic support note

• This is a continuous monitor (fuel system).

• The check engine light illuminates if the PCM detects the above malfunction condition in two consecutive drive cycles or in one drive cycle while the DTC for the same malfunction has been stored in the PCM.

• PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle.

• FREEZE FRAME DATA (Mode 2)/Snapshot data is available.

• DTC is stored in the PCM memory.

POSSIBLE CAUSE

• Misfire

• Erratic signal to PCM

― APP sensor signal malfunction

― ECT sensor signal malfunction

― MAF sensor signal malfunction

― TP sensor signal malfunction

― VSS signal malfunction

• A/F sensor heater malfunction

• A/F sensor malfunction

― Looseness A/F sensor

― A/F sensor deterioration

• Leakage exhaust system

• Air suction in intake air system

• MAF sensor malfunction

• Improper operation of purge control system

• Fuel supply system malfunction

― Pressure regulator malfunction

― Fuel pump unit malfunction

― Fuel leakage on fuel line from fuel distributor and fuel pump

― Fuel filter clogged or restricted

― Fuel return hose clogged

• Ignition system malfunction

― Ignition coil related wiring harness malfunction

― Spark plug malfunction

― Ignition coil malfunction

• Improper operation of variable valve timing control system

• Insufficient engine compression

• Improper operation of fuel injector

• PCM malfunction

STEP	INSPECTION	ACTION
1	IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA (MODE 2) • Perform the Freeze Frame PID Data Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].) • Is the DTC P0171:00 on FREEZE FRAME DATA (Mode 2)?	Yes	Go to the next step.
No	Go to the troubleshooting procedures for DTC on FREEZE FRAME DATA (Mode 2). (See DTC TABLE [MZR 1.6].)
2	VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED • Have the FREEZE FRAME DATA (Mode 2)/snapshot data and DIAGNOSTIC MONITORING TEST RESULTS (fuel system related) been recorded?	Yes	Go to the next step.
No	Record the FREEZE FRAME DATA (Mode 2)/snapshot data and DIAGNOSTIC MONITORING TEST RESULTS on repair order, then go to the next step.
3	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
No	Go to the next step.
4	VERIFY RELATED PENDING CODE AND STORED DTC • Switch the ignition off, then ON (engine off). • Perform the DTC Reading Procedure and Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].) • Are any other DTCs present?	Yes	If misfire DTC is present: • Go to Step 11. If other DTC is present: • Go to the applicable DTC inspection. (See DTC TABLE [MZR 1.6].)
No	If drive ability concern is present: • Go to Step 11. If drive ability concern is not present: • Go to the next step.
5	VERIFY CURRENT INPUT SIGNAL STATUS • Connect the M-MDS to the DLC-2. • Access the following PIDs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].) ― APP1 ― APP2 ― ECT ― MAF ― TP REL ― VSS • Is there any signal that is far out of specification when the ignition is switched to ON and the engine runs? (See PCM INSPECTION [MZR 1.6].)	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.
No	Go to the next step.
6	VERIFY CURRENT INPUT SIGNAL STATUS UNDER FREEZE FRAME DATA (MODE 2) CONDITION • Perform the PID/DATA Monitor and Record Procedure and access the same PIDs as in Step 5 under the FREEZE FRAME DATA (Mode 2) condition. (See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].) • Is there any signal which causes drastic changes?	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.
No	Go to the next step.
7	INSPECT A/F SENSOR HEATER • Inspect the A/F sensor heater. (See AIR FUEL RATIO (A/F) SENSOR INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Replace the A/F sensor, then go to Step 20. (See AIR FUEL RATIO (A/F) SENSOR REMOVAL/INSTALLATION [MZR 1.6].)
No	Go to the next step.
8	INSPECT A/F SENSOR • Reconnect all disconnected connectors. • Inspect the A/F sensor. (See AIR FUEL RATIO (A/F) SENSOR INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Go to the next step.
No	Go to Step 10.
9	INSPECT INSTALLATION OF A/F SENSOR • Inspect if the A/F sensor is loosely installed. • Is the A/F sensor installed securely?	Yes	Replace the A/F sensor, then go to Step 20. (See AIR FUEL RATIO (A/F) SENSOR REMOVAL/INSTALLATION [MZR 1.6].)
No	Retighten the A/F sensor, then go to Step 20. (See AIR FUEL RATIO (A/F) SENSOR REMOVAL/INSTALLATION [MZR 1.6].)
10	INSPECT EXHAUST GAS LEAKAGE • Visually inspect for the exhaust gas leakage between the exhaust manifold and A/F sensor. • Is there any leakage?	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.
No	Go to the next step.
11	VERIFY CURRENT INPUT SIGNAL STATUS OF MAF SENSOR • Connect the M-MDS to the DLC-2. • Start the engine. • Access the MAF PID using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].) • Verify that the MAF PID changes quickly according to engine RPM. • Is the MAF PID value normal? (See PCM INSPECTION [MZR 1.6].)	Yes	Go to Step 13.
No	Go to the next step.
12	INSPECT FOR EXCESSIVE AIR SUCTION OF INTAKE AIR SYSTEM • Visually inspect for loosen, cracks or damages hoses on intake air system. Note • Engine speed may change when rust penetrating agent is sprayed on the air suction area. • Is there any malfunction?	Yes	Repair or replace the source of air suction, then go to Step 20.
No	Replace the MAF/IAT sensor, then go to Step 20. (See MASS AIR FLOW (MAF)/INTAKE AIR TEMPERATURE (IAT) SENSOR REMOVAL/INSTALLATION [MZR 1.6].)
13	INSPECT PURGE CONTROL SYSTEM OPERATION • Perform the Purge Control System Inspection. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.
No	Go to the next step.
14	INSPECT FUEL LINE PRESSURE • Switch the ignition off. Note • If engine will not start, inspect fuel line pressure with ignition is switched to ON. • Inspect fuel line pressure while engine running. (See FUEL LINE PRESSURE INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	If fuel pressure is too high: • Replace the fuel pump unit, then go to Step 20. (See FUEL PUMP UNIT REMOVAL/INSTALLATION [MZR 1.6].) If fuel pressure is low: • Go to the next step.
No	Go to Step 16.
15	INSPECT FUEL LINE • Visually inspect the fuel line from fuel pump to fuel distributor. • Is there any leakage?	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.
No	Inspect the low-pressure side fuel filter for follows: • Foreign materials or stain inside fuel filter. • If foreign materials or stain is found inside fuel filter (low-pressure side): ― Clean of fuel tank and filter. • If foreign materials or stain is not found: ― Replace the fuel pump unit. (See FUEL PUMP UNIT REMOVAL/INSTALLATION [MZR 1.6].) Go to Step 20.
16	INSPECT IGNITION SYSTEM OPERATION • Carry out the spark test. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [MZR 1.6].) • Is strong blue spark visible at each cylinder?	Yes	Go to the next step.
No	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.
17	INSPECT VARIABLE VALVE TIMING CONTROL SYSTEM OPERATION • Perform the Variable Valve Timing Control System Operation Inspection. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.
No	Go to the next step.
18	INSPECT ENGINE COMPRESSION • Inspect the engine compression. (See COMPRESSION INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.
No	Go to the next step.
19	INSPECT FUEL INJECTOR OPERATION • Perform the Fuel Injector Operation Inspection. (See ENGINE CONTROL SYSTEM OPERATION INSPECTION [MZR 1.6].) • Is there any malfunction?	Yes	Repair or replace the malfunctioning parts according to the inspection results, then go to the next step. (See FUEL INJECTOR REMOVAL/INSTALLATION [MZR 1.6].)
No	Go to the next step.
20	VERIFY DTC TROUBLESHOOTING COMPLETED • Always reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See AFTER REPAIR PROCEDURE [MZR 1.6].) • Perform the Drive Mode 03 (A/F sensor heater, HO2S heater, A/F sensor, HO2S and TWC Repair Verification Drive Mode). (See OBD DRIVE MODE [MZR 1.6].) • Perform the Pending Trouble Code Access Procedure. (See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].) • Is the PENDING CODE for this DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [MZR 1.6].) Go to the next step.
No	Go to the next step.
21	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [MZR 1.6].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [MZR 1.6].)
No	DTC troubleshooting completed.

STEP

INSPECTION

ACTION

IDENTIFY TRIGGER DTC FOR FREEZE FRAME DATA (MODE 2)

• Perform the Freeze Frame PID Data Access Procedure.

(See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].)

• Is the DTC P0171:00 on FREEZE FRAME DATA (Mode 2)?

Yes

Go to the next step.

Go to the troubleshooting procedures for DTC on FREEZE FRAME DATA (Mode 2).

(See DTC TABLE [MZR 1.6].)

VERIFY FREEZE FRAME DATA (MODE 2)/SNAPSHOT DATA AND DIAGNOSTIC MONITORING TEST RESULTS HAVE BEEN RECORDED

• Have the FREEZE FRAME DATA (Mode 2)/snapshot data and DIAGNOSTIC MONITORING TEST RESULTS (fuel system related) been recorded?

Yes

Go to the next step.

Record the FREEZE FRAME DATA (Mode 2)/snapshot data and DIAGNOSTIC MONITORING TEST RESULTS on repair order, then go to the next step.

VERIFY RELATED SERVICE INFORMATION AVAILABILITY

• Verify related Service Information availability.

• Is any related Service Information available?

Yes

Perform repair or diagnosis according to the available Service Information.

• If the vehicle is not repaired, go to the next step.

Go to the next step.

VERIFY RELATED PENDING CODE AND STORED DTC

• Switch the ignition off, then ON (engine off).

• Perform the DTC Reading Procedure and Pending Trouble Code Access Procedure.

(See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].)

• Are any other DTCs present?

Yes

If misfire DTC is present:

• Go to Step 11.

If other DTC is present:

• Go to the applicable DTC inspection.

(See DTC TABLE [MZR 1.6].)

If drive ability concern is present:

• Go to Step 11.

If drive ability concern is not present:

• Go to the next step.

VERIFY CURRENT INPUT SIGNAL STATUS

• Connect the M-MDS to the DLC-2.

• Access the following PIDs using the M-MDS.

(See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].)

― APP1

― APP2

― ECT

― MAF

― TP REL

― VSS

• Is there any signal that is far out of specification when the ignition is switched to ON and the engine runs?

(See PCM INSPECTION [MZR 1.6].)

Yes

Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.

Go to the next step.

VERIFY CURRENT INPUT SIGNAL STATUS UNDER FREEZE FRAME DATA (MODE 2) CONDITION

• Perform the PID/DATA Monitor and Record Procedure and access the same PIDs as in Step 5 under the FREEZE FRAME DATA (Mode 2) condition.

(See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].)

• Is there any signal which causes drastic changes?

Yes

Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.

Go to the next step.

INSPECT A/F SENSOR HEATER

• Inspect the A/F sensor heater.

(See AIR FUEL RATIO (A/F) SENSOR INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Replace the A/F sensor, then go to Step 20.

(See AIR FUEL RATIO (A/F) SENSOR REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

INSPECT A/F SENSOR

• Reconnect all disconnected connectors.

• Inspect the A/F sensor.

(See AIR FUEL RATIO (A/F) SENSOR INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Go to the next step.

Go to Step 10.

INSPECT INSTALLATION OF A/F SENSOR

• Inspect if the A/F sensor is loosely installed.

• Is the A/F sensor installed securely?

Yes

Replace the A/F sensor, then go to Step 20.

(See AIR FUEL RATIO (A/F) SENSOR REMOVAL/INSTALLATION [MZR 1.6].)

Retighten the A/F sensor, then go to Step 20.

(See AIR FUEL RATIO (A/F) SENSOR REMOVAL/INSTALLATION [MZR 1.6].)

INSPECT EXHAUST GAS LEAKAGE

• Visually inspect for the exhaust gas leakage between the exhaust manifold and A/F sensor.

• Is there any leakage?

Yes

Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.

Go to the next step.

VERIFY CURRENT INPUT SIGNAL STATUS OF MAF SENSOR

• Connect the M-MDS to the DLC-2.

• Start the engine.

• Access the MAF PID using the M-MDS.

(See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].)

• Verify that the MAF PID changes quickly according to engine RPM.

• Is the MAF PID value normal?

(See PCM INSPECTION [MZR 1.6].)

Yes

Go to Step 13.

Go to the next step.

INSPECT FOR EXCESSIVE AIR SUCTION OF INTAKE AIR SYSTEM

• Visually inspect for loosen, cracks or damages hoses on intake air system.

Note

• Engine speed may change when rust penetrating agent is sprayed on the air suction area.

• Is there any malfunction?

Yes

Repair or replace the source of air suction, then go to Step 20.

Replace the MAF/IAT sensor, then go to Step 20.

(See MASS AIR FLOW (MAF)/INTAKE AIR TEMPERATURE (IAT) SENSOR REMOVAL/INSTALLATION [MZR 1.6].)

INSPECT PURGE CONTROL SYSTEM OPERATION

• Perform the Purge Control System Inspection.

(See ENGINE CONTROL SYSTEM OPERATION INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.

Go to the next step.

INSPECT FUEL LINE PRESSURE

• Switch the ignition off.

Note

• If engine will not start, inspect fuel line pressure with ignition is switched to ON.

• Inspect fuel line pressure while engine running.

(See FUEL LINE PRESSURE INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

If fuel pressure is too high:

• Replace the fuel pump unit, then go to Step 20.

(See FUEL PUMP UNIT REMOVAL/INSTALLATION [MZR 1.6].)

If fuel pressure is low:

• Go to the next step.

Go to Step 16.

INSPECT FUEL LINE

• Visually inspect the fuel line from fuel pump to fuel distributor.

• Is there any leakage?

Yes

Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.

Inspect the low-pressure side fuel filter for follows:

• Foreign materials or stain inside fuel filter.

• If foreign materials or stain is found inside fuel filter (low-pressure side):

― Clean of fuel tank and filter.

• If foreign materials or stain is not found:

― Replace the fuel pump unit.

(See FUEL PUMP UNIT REMOVAL/INSTALLATION [MZR 1.6].)

Go to Step 20.

INSPECT IGNITION SYSTEM OPERATION

• Carry out the spark test.

(See ENGINE CONTROL SYSTEM OPERATION INSPECTION [MZR 1.6].)

• Is strong blue spark visible at each cylinder?

Yes

Go to the next step.

Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.

INSPECT VARIABLE VALVE TIMING CONTROL SYSTEM OPERATION

• Perform the Variable Valve Timing Control System Operation Inspection.

(See ENGINE CONTROL SYSTEM OPERATION INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.

Go to the next step.

INSPECT ENGINE COMPRESSION

• Inspect the engine compression.

(See COMPRESSION INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Repair or replace the malfunctioning parts according to the inspection results, then go to Step 20.

Go to the next step.

INSPECT FUEL INJECTOR OPERATION

• Perform the Fuel Injector Operation Inspection.

(See ENGINE CONTROL SYSTEM OPERATION INSPECTION [MZR 1.6].)

• Is there any malfunction?

Yes

Repair or replace the malfunctioning parts according to the inspection results, then go to the next step.

(See FUEL INJECTOR REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

VERIFY DTC TROUBLESHOOTING COMPLETED

• Always reconnect all disconnected connectors.

• Clear the DTC from the PCM memory using the M-MDS.

(See AFTER REPAIR PROCEDURE [MZR 1.6].)

• Perform the Drive Mode 03 (A/F sensor heater, HO2S heater, A/F sensor, HO2S and TWC Repair Verification Drive Mode).

(See OBD DRIVE MODE [MZR 1.6].)

• Perform the Pending Trouble Code Access Procedure.

(See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].)

• Is the PENDING CODE for this DTC present?

Yes

Repeat the inspection from Step 1.

• If the malfunction recurs, replace the PCM.

(See PCM REMOVAL/INSTALLATION [MZR 1.6].)

Go to the next step.

VERIFY AFTER REPAIR PROCEDURE

• Perform the “AFTER REPAIR PROCEDURE”.

(See AFTER REPAIR PROCEDURE [MZR 1.6].)

• Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [MZR 1.6].)

DTC troubleshooting completed.