DTC U0305:00 [SKYACTIV-D 2.2]

id0102s4901100

DTC U0305:00

Vehicle control module (V/C-module) error

DETECTION CONDITION

•  With the battery voltage 10 V or more, any of the following conditions is continuously met for 5 s.

―  Check sum error in signal from radar unit

―  Counter error in signal from radar unit

Diagnostic support note

•  This is a continuous monitor (other).

•  The check engine light does not illuminate.

•  FREEZE FRAME DATA (Mode 2)/Snapshot data is not available.

•  DTC is not stored in the PCM memory.

FAIL-SAFE FUNCTION

Not applicable

POSSIBLE CAUSE

•  CAN drive error (instrument cluster or PCM)

•  CAN communication line malfunction between vehicle control module (V/C-module) and PCM

―  Vehicle control module (V/C-module) terminal S—Front body control module (FBCM) terminal 2K

―  Vehicle control module (V/C-module) terminal U—Front body control module (FBCM) terminal 2I

―  Front body control module (FBCM) terminal 2P—PCM terminal 2AK

―  Front body control module (FBCM) terminal 2N—PCM terminal 2AL

•  Front body control module (FBCM) malfunction

•  Vehicle control module (V/C-module) connector or terminals malfunction

•  PCM connector or terminals malfunction

•  Vehicle control module (V/C-module) malfunction

•  PCM malfunction

DTC U0305:00	Vehicle control module (V/C-module) error
DETECTION CONDITION	• With the battery voltage 10 V or more, any of the following conditions is continuously met for 5 s. ― Check sum error in signal from radar unit ― Counter error in signal from radar unit Diagnostic support note • This is a continuous monitor (other). • The check engine light does not illuminate. • FREEZE FRAME DATA (Mode 2)/Snapshot data is not available. • DTC is not stored in the PCM memory.
FAIL-SAFE FUNCTION	Not applicable
POSSIBLE CAUSE	• CAN drive error (instrument cluster or PCM) • CAN communication line malfunction between vehicle control module (V/C-module) and PCM ― Vehicle control module (V/C-module) terminal S—Front body control module (FBCM) terminal 2K ― Vehicle control module (V/C-module) terminal U—Front body control module (FBCM) terminal 2I ― Front body control module (FBCM) terminal 2P—PCM terminal 2AK ― Front body control module (FBCM) terminal 2N—PCM terminal 2AL • Front body control module (FBCM) malfunction • Vehicle control module (V/C-module) connector or terminals malfunction • PCM connector or terminals malfunction • Vehicle control module (V/C-module) malfunction • PCM malfunction

Repeatability Verification Procedure

1. Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC [SKYACTIV-D 2.2].)

2. Start the engine.

Diagnostic Procedure

STEP

INSPECTION

ACTION

1

VERIFY RELATED SERVICE INFORMATION AVAILABILITY

•  Verify related Service Information availability.

•  Is any related Service Information available?

Yes

Perform repair or diagnosis according to the available Service Information.

•  If the vehicle is not repaired, go to the next step.

No

Go to the next step.

2

VERIFY DTC FOR MODULE COMMUNICATION

•  Switch the ignition off, then ON (engine off).

•  Perform the DTC Reading Procedure.
(See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 2.2].)

•  Are any other PENDING CODEs and/or DTCs present?

Yes

Go to the applicable PENDING CODE or DTC inspection.

(See DTC TABLE [SKYACTIV-D 2.2].)

No

Go to the next step.

3

CONFIRM FRONT BODY CONTROL MODULE (FBCM) DTC

•  Perform the front body control module (FBCM) DTC inspection using the M-MDS.
(See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [FRONT BODY CONTROL MODULE (FBCM)].)

No

Go to the next step.

4

CONFIRM VEHICLE CONTROL MODULE (V/C-MODULE) DTC

•  Perform the vehicle control module (V/C-module) DTC inspection using the M-MDS.
(See DTC INSPECTION [VEHICLE CONTROL MODULE (V/C-MODULE)].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [VEHICLE CONTROL MODULE (V/C-MODULE)].)

No

Go to the next step.

5

CONFIRM INSTRUMENT CLUSTER DTC

•  Perform the instrument cluster DTC inspection using the M-MDS.
(See DTC INSPECTION [INSTRUMENT CLUSTER].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [INSTRUMENT CLUSTER].)

No

Go to the next step.

6

INSPECT VEHICLE CONTROL MODULE (V/C-MODULE) CONNECTOR CONDITION

•  Switch the ignition off.

•  Disconnect the vehicle control module (V/C-module) connector.

•  Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

•  Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to Step 8.

No

Go to the next step.

7

INSPECT PCM CONNECTOR CONDITION

•  Disconnect the PCM connector.

•  Inspect for poor connection (such as damaged/pulled-out pins, corrosion).

•  Is there any malfunction?

Yes

Repair or replace the connector and/or terminals, then go to the next step.

No

CAN communication line can be considered the cause.

•  Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals:

―  Vehicle control module (V/C-module) terminal S—Front body control module (FBCM) terminal 2K

―  Vehicle control module (V/C-module) terminal U—Front body control module (FBCM) terminal 2I

―  Front body control module (FBCM) terminal 2P—PCM terminal 2AK

―  Front body control module (FBCM) terminal 2N—PCM terminal 2AL

If there is a common connector:

―  Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a malfunction.

―  Repair or replace the malfunctioning part.

If there is no common connector:

―  Repair or replace the wiring harness.

If the malfunction recurs, replace the vehicle control module (V/C-module).

(See VEHICLE CONTROL MODULE (V/C-MODULE) REMOVAL/INSTALLATION [MAZDA RADAR CRUISE CONTROL (MRCC) SYSTEM].)

Go to the next step.

8

VERIFY DTC TROUBLESHOOTING COMPLETED

•  Always reconnect all disconnected connectors.

•  Clear the DTC from the PCM memory using the M-MDS.
(See CLEARING DTC [SKYACTIV-D 2.2].)

•  Implement the repeatability verification procedure.
(See Repeatability Verification Procedure.)

•  Perform the DTC Reading Procedure.
(See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 2.2].)

•  Is the same DTC present?

Yes

Repeat the inspection from Step 1.

•  If the malfunction recurs, replace the PCM.
(See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].)

Go to the next step.

No

Go to the next step.

9

VERIFY AFTER REPAIR PROCEDURE

•  Perform the “AFTER REPAIR PROCEDURE”.
(See AFTER REPAIR PROCEDURE [SKYACTIV-D 2.2].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [SKYACTIV-D 2.2].)

No

DTC troubleshooting completed.

STEP	INSPECTION		ACTION
1	VERIFY RELATED SERVICE INFORMATION AVAILABILITY • Verify related Service Information availability. • Is any related Service Information available?	Yes	Perform repair or diagnosis according to the available Service Information. • If the vehicle is not repaired, go to the next step.
1		No	Go to the next step.
2	VERIFY DTC FOR MODULE COMMUNICATION • Switch the ignition off, then ON (engine off). • Perform the DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 2.2].) • Are any other PENDING CODEs and/or DTCs present?	Yes	Go to the applicable PENDING CODE or DTC inspection. (See DTC TABLE [SKYACTIV-D 2.2].)
2		No	Go to the next step.
3	CONFIRM FRONT BODY CONTROL MODULE (FBCM) DTC • Perform the front body control module (FBCM) DTC inspection using the M-MDS. (See DTC INSPECTION [FRONT BODY CONTROL MODULE (FBCM)].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [FRONT BODY CONTROL MODULE (FBCM)].)
3		No	Go to the next step.
4	CONFIRM VEHICLE CONTROL MODULE (V/C-MODULE) DTC • Perform the vehicle control module (V/C-module) DTC inspection using the M-MDS. (See DTC INSPECTION [VEHICLE CONTROL MODULE (V/C-MODULE)].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [VEHICLE CONTROL MODULE (V/C-MODULE)].)
4		No	Go to the next step.
5	CONFIRM INSTRUMENT CLUSTER DTC • Perform the instrument cluster DTC inspection using the M-MDS. (See DTC INSPECTION [INSTRUMENT CLUSTER].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [INSTRUMENT CLUSTER].)
5		No	Go to the next step.
6	INSPECT VEHICLE CONTROL MODULE (V/C-MODULE) CONNECTOR CONDITION • Switch the ignition off. • Disconnect the vehicle control module (V/C-module) connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to Step 8.
6		No	Go to the next step.
7	INSPECT PCM CONNECTOR CONDITION • Disconnect the PCM connector. • Inspect for poor connection (such as damaged/pulled-out pins, corrosion). • Is there any malfunction?	Yes	Repair or replace the connector and/or terminals, then go to the next step.
7		No	CAN communication line can be considered the cause. • Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: ― Vehicle control module (V/C-module) terminal S—Front body control module (FBCM) terminal 2K ― Vehicle control module (V/C-module) terminal U—Front body control module (FBCM) terminal 2I ― Front body control module (FBCM) terminal 2P—PCM terminal 2AK ― Front body control module (FBCM) terminal 2N—PCM terminal 2AL If there is a common connector: ― Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a malfunction. ― Repair or replace the malfunctioning part. If there is no common connector: ― Repair or replace the wiring harness. If the malfunction recurs, replace the vehicle control module (V/C-module). (See VEHICLE CONTROL MODULE (V/C-MODULE) REMOVAL/INSTALLATION [MAZDA RADAR CRUISE CONTROL (MRCC) SYSTEM].) Go to the next step.
8	VERIFY DTC TROUBLESHOOTING COMPLETED • Always reconnect all disconnected connectors. • Clear the DTC from the PCM memory using the M-MDS. (See CLEARING DTC [SKYACTIV-D 2.2].) • Implement the repeatability verification procedure. (See Repeatability Verification Procedure.) • Perform the DTC Reading Procedure. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 2.2].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the PCM. (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].) Go to the next step.
8		No	Go to the next step.
9	VERIFY AFTER REPAIR PROCEDURE • Perform the “AFTER REPAIR PROCEDURE”. (See AFTER REPAIR PROCEDURE [SKYACTIV-D 2.2].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [SKYACTIV-D 2.2].)
9		No	DTC troubleshooting completed.