DTC P0615:11 [START STOP UNIT]

id0902p6022000

Description

Starter relay circuit malfunction

Detection condition

•  Start stop unit detects that the starter relay monitor circuit voltage of less than 2.2 V for 0.2 s or more with the ignition switched off.

Fail-safe function

Not applicable

Possible cause

•  DTCs are stored in the PCM.

•  Starter relay malfunction

•  Start stop unit connector or terminal malfunction

•  PCM connector malfunction

•  Short to ground in wiring harness between the following terminals:

―  Start stop unit terminal 1D—Starter relay terminal E

―  Start stop unit terminal 1D—PCM terminal 2AZ (SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5)

―  Start stop unit terminal 1D—PCM terminal 2BF (SKYACTIV-D 1.5, SKYACTIV-D 2.2)

―  Start stop unit terminal 1D—PCM terminal 1F (MZR 1.6)

―  Start stop unit terminal 2V—Starter relay terminal A

•  PCM malfunction

•  Start stop unit malfunction

Description	Starter relay circuit malfunction
Detection condition	• Start stop unit detects that the starter relay monitor circuit voltage of less than 2.2 V for 0.2 s or more with the ignition switched off.
Fail-safe function	Not applicable
Possible cause	• DTCs are stored in the PCM. • Starter relay malfunction • Start stop unit connector or terminal malfunction • PCM connector malfunction • Short to ground in wiring harness between the following terminals: ― Start stop unit terminal 1D—Starter relay terminal E ― Start stop unit terminal 1D—PCM terminal 2AZ (SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5) ― Start stop unit terminal 1D—PCM terminal 2BF (SKYACTIV-D 1.5, SKYACTIV-D 2.2) ― Start stop unit terminal 1D—PCM terminal 1F (MZR 1.6) ― Start stop unit terminal 2V—Starter relay terminal A • PCM malfunction • Start stop unit malfunction

Diagnostic Procedure

Step	Inspection		Action
1	VERIFY PCM DTCs • Retrieve the PCM DTCs using the M-MDS. (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 1.5].) (See ON-BOARD DIAGNOSTIC TEST [SKYACTIV-D 2.2].) (See ON-BOARD DIAGNOSTIC TEST [MZR 1.6].) • Are any DTCs displayed?	Yes	Repair or replace the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See DTC TABLE [SKYACTIV-D 1.5].) (See DTC TABLE [SKYACTIV-D 2.2].) (See DTC TABLE [MZR 1.6].)
1		No	Go to the next step.
2	INSPECT STARTER RELAY • Switch the ignition off. • Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) • Remove the starter relay. (See RELAY LOCATION.) • Inspect the starter relay. (See RELAY INSPECTION.) • Is the starter relay normal?	Yes	Go to the next step.
2		No	Replace the starter relay, then go to Step 7. (See RELAY LOCATION.)
3	INSPECT START STOP UNIT CONNECTOR CONDITION • Disconnect the start stop unit connector. • Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. • Is the connector normal?	Yes	Go to the next step.
3		No	Repair or replace the connector, then go to Step 7.
4	INSPECT PCM CONNECTOR CONDITION • Disconnect the PCM connector. • Inspect the connector engagement and connection condition and inspect the terminals for damage, deformation, corrosion, or disconnection. • Is the connector normal?	Yes	Go to the next step.
4		No	Repair or replace the connector, then go to Step 7.
5	INSPECT FOR SHORT TO GROUND IN STARTER RELAY CIRCUIT • Verify that the starter relay is removed. • Verify that the start stop unit and PCM connectors are disconnected. • Inspect for continuity between the following terminals (wiring harness-side) and body ground: ― Start stop unit terminal 1D ― Start stop unit terminal 2V • Is there continuity?	Yes	Refer to the wiring diagram and verify whether or not there is a common connector between the following terminals: • Start stop unit terminal 1D—Starter relay terminal E • Start stop unit terminal 1D—PCM terminal 2AZ (SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5) • Start stop unit terminal 1D—PCM terminal 2BF (SKYACTIV-D 1.5, SKYACTIV-D 2.2) • Start stop unit terminal 1D—PCM terminal 1F (MZR 1.6) • Start stop unit terminal 2V—Starter relay terminal A If there is a common connector: • Determine the malfunctioning part by inspecting the common connector and the terminal for corrosion, damage, or pin disconnection, and the common wiring harness for a short to ground. • Repair or replace the malfunctioning part. If there is no common connector: • Repair or replace the wiring harness which has a short to ground. Go to Step 7.
5		No	Go to the next step.
6	PERFORM DTC INSPECTION AND VERIFY PCM MALFUNCTION • Always reconnect all disconnected connectors. • Reconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) • Clear the DTC for the start stop unit using the M-MDS. (See CLEARING DTC [START STOP UNIT].) • Switch the ignition off and wait for 1 s or more. • Retrieve the start stop unit DTCs using the M-MDS. (See DTC INSPECTION [START STOP UNIT].) • Is the same DTC displayed?	Yes	Replace the PCM, then go to the next step. (See PCM REMOVAL/INSTALLATION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 1.5].) (See PCM REMOVAL/INSTALLATION [SKYACTIV-D 2.2].) (See PCM REMOVAL/INSTALLATION [MZR 1.6].)
6		No	Go to Step 8.
7	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Always reconnect all disconnected connectors. • Reconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) • Clear the DTC for the start stop unit using the M-MDS. (See CLEARING DTC [START STOP UNIT].) • Switch the ignition off and wait for 1 s or more. • Retrieve the start stop unit DTCs using the M-MDS. (See DTC INSPECTION [START STOP UNIT].) • Is the same DTC displayed?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the start stop unit. (See START STOP UNIT REMOVAL/INSTALLATION.) Go to the next step.
7		No	Go to the next step.
8	VERIFY IF OTHER DTCs DISPLAYED • Are any other DTCs displayed?	Yes	Repair or replace the malfunctioning part according to the applicable DTC troubleshooting. (See DTC TABLE [START STOP UNIT].)
8		No	DTC troubleshooting completed.