STEERING SWITCH REMOVAL/INSTALLATION

id092000822500

Warning
•  Handling the driver-side air bag module improperly can accidentally operate (deploy) the air bag module, which may seriously injure you. Read the service warnings and cautions before handling the air bag module. (See AIR BAG SYSTEM SERVICE WARNINGS.) (See AIR BAG SYSTEM SERVICE CAUTIONS.)

Without Steering Shift Switch


Steering switch removal/installation

1.  Switch the ignition off.

2.  Disconnect the negative battery cable and wait for 1 min or more. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

3.  Remove the driver-side air bag module. (See DRIVER-SIDE AIR BAG MODULE REMOVAL.) (See DRIVER-SIDE AIR BAG MODULE INSTALLATION.)

4.  Remove the steering wheel. (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)

5.  Affix protective tape to the gaps between the steering wheel and cover as shown in the figure.

am3uuw00011853

6.  Using a tape-wrapped flathead screwdriver, press the cover tabs in the direction of the arrows shown in the figure to detach the cover tabs from the steering wheel.

am3zzw00015847

7.  Insert the fastener remover into the clearance between the steering wheel and cover as shown in the figure.

ac5jjw00000934

8.  Move the fastener remover in the direction of the arrow shown in the figure and detach cover tab from the steering wheel.

9.  Remove the cover while detaching the pins from the steering wheel.

ac5jjw00000943

10.  While pressing the clip tabs in the direction of the arrows (1) shown in the figure, press the clip in the direction of the arrow (2) to detach the clip tabs from the steering wheel.

am3zzw00015848

11.  Detach the clip.

12.  Warm up the shaded area shown in the figure and soften the hard plastic area of the steering wheel using a heat gun.

13.  While pressing the tabs of the steering switch in the direction of the arrows (1) shown in the figure, press the steering switch in the direction of the arrow (2) to detach the tabs of the steering switch from the steering wheel.

ac5wzw00007135

14.  Warm up the shaded area shown in the figure and soften the hard plastic area of the steering wheel using a heat gun.

15.  Insert a fastener remover into the position shown in the figure.

am3zzw00015849

16.  Move the fastener remover straight in the direction shown in the figure and remove the tabs of the steering switch from the steering wheel.

Caution
•  When removing the pins of the steering switch, pull them out straight. If the fastener remover is moved at an angle, the pins could be damaged.
Note
•  Because the pins of the steering switch are installed to the hard plastic area of the steering wheel, the engagement is strong.
ac5uuw00002653

17.  Remove the steering switch while detaching the pin and tabs of the steering wheel.

ac5jjw00000944

18.  Install in the reverse order of removal.


Hub cover removal/installation

1.  Switch the ignition off.

2.  Disconnect the negative battery cable and wait for 1 min or more. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

3.  Remove the following parts:

(1)  Driver-side air bag module (See DRIVER-SIDE AIR BAG MODULE REMOVAL.) (See DRIVER-SIDE AIR BAG MODULE INSTALLATION.)
(2)  Steering wheel (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)
(3)  Steering switch (See Steering switch removal/installation.)

4.  Affix protective tape shown in the figure.

ac5wzw00007137

5.  Warm up the shaded area shown in the figure and soften the hard plastic area of the steering wheel using a heat gun.

6.  Press the tab in the direction of arrow shown in the figure,detach it.

am3zzw00015837

7.  Insert a plastic remover tool, move it in the direction of the arrow shown in the figure, detach the tabs.

ac5wzw00007139

8.  Insert a remover tool, move it in the direction of the arrow shown in the figure, remove the pin.

ac5wzw00007140

9.  Remove the hub cover.

10.  Install in the reverse order of removal.


With Steering Shift Switch


Steering switch removal/installation

1.  Switch the ignition off.

2.  Disconnect the negative battery cable and wait for 1 min or more. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

3.  Remove the driver-side air bag module. (See DRIVER-SIDE AIR BAG MODULE REMOVAL.) (See DRIVER-SIDE AIR BAG MODULE INSTALLATION.)

4.  Remove the steering wheel. (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)

5.  Remove the screws.

am3zzw00015550

6.  Disconnect the connectors.

7.  While pressing the pin tabs in the direction of arrows (1) shown in the figure, press the pin in the direction of arrow (2) to detach the cover pin from the steering wheel.

am3zzw00015850

8.  Using a tape-wrapped flathead screwdriver, press the cover tabs in the direction of the arrows shown in the figure to detach the cover tabs from the steering wheel.

am3zzw00015847

9.  Remove the cover.

am6zzw00011318

10.  While pressing the clip tabs in the direction of the arrows (1) shown in the figure, press the clip in the direction of the arrow (2) to detach the clip tabs from the steering wheel.

am3zzw00015851

11.  Detach the clip.

12.  Warm up the shaded area shown in the figure and soften the hard plastic area of the steering wheel using a heat gun.

13.  While pressing the tabs of the steering switch in the direction of the arrows (1) shown in the figure, press the steering switch in the direction of the arrow (2) to detach the tabs of the steering switch from the steering wheel.

ac5wzw00007135

14.  Warm up the shaded area shown in the figure and soften the hard plastic area of the steering wheel using a heat gun.

15.  Insert a fastener remover into the position shown in the figure.

am3zzw00015849

16.  Move the fastener remover straight in the direction shown in the figure and remove the tabs of the steering switch from the steering wheel.

Caution
•  When removing the pins of the steering switch, pull them out straight. If the fastener remover is moved at an angle, the pins could be damaged.
Note
•  Because the pins of the steering switch are installed to the hard plastic area of the steering wheel, the engagement is strong.
ac5uuw00002653

17.  Remove the steering switch while detaching the pin and tabs of the steering wheel.

ac5jjw00000944

18.  Install in the reverse order of removal.


Hub cover removal/installation

1.  Switch the ignition off.

2.  Disconnect the negative battery cable and wait for 1 min or more. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

3.  Remove the following parts:

(1)  Driver-side air bag module (See DRIVER-SIDE AIR BAG MODULE REMOVAL.) (See DRIVER-SIDE AIR BAG MODULE INSTALLATION.)
(2)  Steering wheel (See STEERING WHEEL AND COLUMN REMOVAL/INSTALLATION.)
(3)  Steering switch (See Steering switch removal/installation.)

4.  Affix protective tape shown in the figure.

ac5wzw00007137

5.  Warm up the shaded area shown in the figure and soften the hard plastic area of the steering wheel using a heat gun.

6.  Press the tab in the direction of arrow shown in the figure,detach it.

am3zzw00015837

7.  Insert a plastic remover tool, move it in the direction of the arrow shown in the figure, detach the tabs.

ac5wzw00007139

8.  Insert a remover tool, move it in the direction of the arrow shown in the figure, remove the pin.

ac5wzw00007140

9.  Remove the hub cover.

10.  Install in the reverse order of removal.