BONNET RELEASE LEVER AND RELEASE CABLE REMOVAL/INSTALLATION

id091400006600

Bonnet Release Lever

1.  While pulling the bonnet release lever, insert a tape-wrapped flathead screwdriver into the position shown in the figure.

am3zzw00013545

2.  Move the tape-wrapped flathead screwdriver in the direction of arrow (1) shown in the figure to press the tab, and pull the bonnet release cable in the direction of arrow (2) to detach the bonnet release lever from the lower panel.

Caution

•  Remove the bonnet release lever while being careful not to damage the bonnet release cable with the flathead screwdriver.

3.  Pull the bonnet release lever to remove it from the lower panel.

am3zzw00013546

4.  Disconnect the bonnet release cable from the bonnet release lever.

5.  Install in the reverse order of removal.

Bonnet Release Cable

L.H.D.

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the following parts:

(1)  Set plate (See SET PLATE REMOVAL/INSTALLATION.)

(2)  Front bumper (See FRONT BUMPER REMOVAL/INSTALLATION.)

(3)  Front combination light (See FRONT COMBINATION LIGHT REMOVAL/INSTALLATION.)

(4)  Shroud upper member (See SHROUD UPPER MEMBER REMOVAL/INSTALLATION.)

(5)  Front mudguard (Driver's side) (See MUDGUARD REMOVAL/INSTALLATION.)

(6)  Front fender insulator No.1 (See FRONT FENDER INSULATOR No.1 REMOVAL/INSTALLATION.)

(7)  Bonnet release lever (See Bonnet Release Lever.)

3.  Remove the bonnet latch protector. (See BONNET LATCH REMOVAL/INSTALLATION.)

4.  Disconnect the bonnet release cable from the bonnet latch.

5.  Remove the bonnet release cable from clip.

am3zzw00013547

6.  Press the grommet into the cabin side.

7.  Remove the bonnet release cable from the cabin side.

8.  Install in the reverse order of removal.

R.H.D.

1.  Disconnect the negative battery cable. (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [MZR 1.6].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-G 1.5, SKYACTIV-G 2.0, SKYACTIV-G 2.5].) (See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 2.2].)(See NEGATIVE BATTERY CABLE DISCONNECTION/CONNECTION [SKYACTIV-D 1.5].)

2.  Remove the following parts:

(1)  Set plate (See SET PLATE REMOVAL/INSTALLATION.)

(2)  Front bumper (See FRONT BUMPER REMOVAL/INSTALLATION.)

(3)  Front combination light (See FRONT COMBINATION LIGHT REMOVAL/INSTALLATION.)

(4)  Shroud upper member (See SHROUD UPPER MEMBER REMOVAL/INSTALLATION.)

(5)  Front mudguard (Driver's side) (See MUDGUARD REMOVAL/INSTALLATION.)

(6)  Front fender insulator No.1 (See FRONT FENDER INSULATOR No.1 REMOVAL/INSTALLATION.)

(7)  Bonnet release lever (See Bonnet Release Lever.)

3.  Remove the bonnet latch protector. (See BONNET LATCH REMOVAL/INSTALLATION.)

4.  Disconnect the bonnet release cable from the bonnet latch.

5.  Remove the bonnet release cable from clip A and clip B.

am3zzw00013724

6.  Press the grommet into the cabin side.

7.  Remove the bonnet release cable from the cabin side.

8.  Install in the reverse order of removal.