DTC U0316:09 [VEHICLE CONTROL MODULE (V/C-MODULE)]

id0102i0002400

System malfunction location

Error signal received from DSC HU/CM

Detection condition

•  There is an error in the following signals sent from the DSC HU/CM.

―  Yaw rate signal

―  Lateral-G signal

―  Longitudinal-G signal

―  Wheel speed signal

―  Brake fluid pressure signal

―  Cruise control system control signal

―  Signal error in brake light circuit

Fail-safe

•  Inhibits the mazda radar cruise control (MRCC) system control

•  Inhibits the smart brake support (SBS) system control

•  Inhibits the distance recognition support system (DRSS) control^*1

^*1: Enabled depending on malfunction content.

Possible cause

•  SAS control module malfunction

•  DSC HU/CM malfunction

•  Rear body control module (RBCM) malfunction

•  Vehicle control module (V/C-module) malfunction

System wiring diagram

•  Not applicable

System malfunction location	Error signal received from DSC HU/CM
Detection condition	• There is an error in the following signals sent from the DSC HU/CM. ― Yaw rate signal ― Lateral-G signal ― Longitudinal-G signal ― Wheel speed signal ― Brake fluid pressure signal ― Cruise control system control signal ― Signal error in brake light circuit
Fail-safe	• Inhibits the mazda radar cruise control (MRCC) system control • Inhibits the smart brake support (SBS) system control • Inhibits the distance recognition support system (DRSS) control^1 ^1: Enabled depending on malfunction content.
Possible cause	• SAS control module malfunction • DSC HU/CM malfunction • Rear body control module (RBCM) malfunction • Vehicle control module (V/C-module) malfunction
System wiring diagram	• Not applicable

Diagnostic Procedure

Step

Inspection

Action

1

PERFORM DTC INSPECTION FOR SAS CONTROL MODULE

•  Perform the SAS control module DTC inspection using the M-MDS.
(See DTC INSPECTION.)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE.)

Then go to Step 5.

No

Go to the next step.

2

PERFORM DTC INSPECTION FOR DSC HU/CM

•  Perform the DSC HU/CM DTC inspection using the M-MDS.
(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].)

Then go to Step 5.

No

Go to the next step.

3

PERFORM DTC INSPECTION FOR REAR BODY CONTROL MODULE (RBCM)

•  Perform the rear body control module (RBCM) DTC inspection using the M-MDS.
(See DTC INSPECTION [REAR BODY CONTROL MODULE (RBCM)].)

•  Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See DTC TABLE [REAR BODY CONTROL MODULE (RBCM)].)

Then go to Step 5.

No

Go to the next step.

4

PERFORM DTC INSPECTION FOR VEHICLE CONTROL MODULE (V/C-MODULE)

•  Clear vehicle control module (V/C-module) DTCs using the M-MDS.
(See CLEARING DTC [VEHICLE CONTROL MODULE (V/C-MODULE)].)

•  Switch the ignition ON (engine on).

•  Perform the vehicle control module (V/C-module) DTC inspection using the M-MDS.
(See DTC INSPECTION [VEHICLE CONTROL MODULE (V/C-MODULE)].)

•  Is the same DTC present?

Yes

Replace the DSC HU/CM, then go to the next step.

(See DSC HU/CM REMOVAL/INSTALLATION.)

No

Go to the next step.

5

VERIFY THAT REPAIRS HAVE BEEN COMPLETED

•  Clear vehicle control module (V/C-module) DTCs using the M-MDS.
(See CLEARING DTC.)

•  Switch the ignition ON (engine on).

•  Drive the vehicle at 40 km/h (25 mph) or more for 3 min or more.

•  Perform the vehicle control module (V/C-module) DTC inspection using the M-MDS.
(See DTC INSPECTION [VEHICLE CONTROL MODULE (V/C-MODULE)].)

•  Is the same DTC present?

Yes

Repeat the inspection from Step 1.

•  If the malfunction recurs, replace the vehicle control module (V/C-module).
(See VEHICLE CONTROL MODULE (V/C-MODULE) REMOVAL/INSTALLATION [MAZDA RADAR CRUISE CONTROL (MRCC) SYSTEM].)

Go to the next step.

No

Go to the next step.

6

VERIFY THAT NO OTHER DTCs ARE PRESENT

•  Verify other DTCs displayed.

•  Are any other DTCs output?

Yes

Perform the corresponding DTC inspection.

No

DTC troubleshooting completed.

Step	Inspection		Action
1	PERFORM DTC INSPECTION FOR SAS CONTROL MODULE • Perform the SAS control module DTC inspection using the M-MDS. (See DTC INSPECTION.) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE.) Then go to Step 5.
1		No	Go to the next step.
2	PERFORM DTC INSPECTION FOR DSC HU/CM • Perform the DSC HU/CM DTC inspection using the M-MDS. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See ON-BOARD DIAGNOSIS [DYNAMIC STABILITY CONTROL (DSC)].) Then go to Step 5.
2		No	Go to the next step.
3	PERFORM DTC INSPECTION FOR REAR BODY CONTROL MODULE (RBCM) • Perform the rear body control module (RBCM) DTC inspection using the M-MDS. (See DTC INSPECTION [REAR BODY CONTROL MODULE (RBCM)].) • Are any DTCs present?	Yes	Go to the applicable DTC inspection. (See DTC TABLE [REAR BODY CONTROL MODULE (RBCM)].) Then go to Step 5.
3		No	Go to the next step.
4	PERFORM DTC INSPECTION FOR VEHICLE CONTROL MODULE (V/C-MODULE) • Clear vehicle control module (V/C-module) DTCs using the M-MDS. (See CLEARING DTC [VEHICLE CONTROL MODULE (V/C-MODULE)].) • Switch the ignition ON (engine on). • Perform the vehicle control module (V/C-module) DTC inspection using the M-MDS. (See DTC INSPECTION [VEHICLE CONTROL MODULE (V/C-MODULE)].) • Is the same DTC present?	Yes	Replace the DSC HU/CM, then go to the next step. (See DSC HU/CM REMOVAL/INSTALLATION.)
4		No	Go to the next step.
5	VERIFY THAT REPAIRS HAVE BEEN COMPLETED • Clear vehicle control module (V/C-module) DTCs using the M-MDS. (See CLEARING DTC.) • Switch the ignition ON (engine on). • Drive the vehicle at 40 km/h (25 mph) or more for 3 min or more. • Perform the vehicle control module (V/C-module) DTC inspection using the M-MDS. (See DTC INSPECTION [VEHICLE CONTROL MODULE (V/C-MODULE)].) • Is the same DTC present?	Yes	Repeat the inspection from Step 1. • If the malfunction recurs, replace the vehicle control module (V/C-module). (See VEHICLE CONTROL MODULE (V/C-MODULE) REMOVAL/INSTALLATION [MAZDA RADAR CRUISE CONTROL (MRCC) SYSTEM].) Go to the next step.
5		No	Go to the next step.
6	VERIFY THAT NO OTHER DTCs ARE PRESENT • Verify other DTCs displayed. • Are any other DTCs output?	Yes	Perform the corresponding DTC inspection.
6		No	DTC troubleshooting completed.